Cylinder 11 only exists on V12 engines, such as those from BMW, Mercedes-Benz, Ferrari, Lamborghini and Aston Martin. A P0211 code means the engine computer found an electrical fault in the fuel injector circuit for cylinder 11.
Because these engines are complex and often use direct injection, this guide explains the code, the tests you can do safely and when to leave the work to a specialist.
P0211 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 2 | Fuel and air metering | The fault involves fuel and air metering, such as injectors, the fuel pump, throttle sensors or boost control. |
| 11 | Specific fault | Injector Circuit Malfunction, Cylinder 11 |
What the P0211 Code Means
The SAE J2012 standard defines the P0211 code as Injector Circuit Malfunction, Cylinder 11. On most port injection engines, the injector gets battery voltage from a fuse or relay whenever the engine runs. The powertrain control module (PCM) opens the injector by grounding its control wire for a few milliseconds, then lets go so the injector snaps shut.
Each injector has its own driver inside the PCM, and the PCM watches that circuit every time it switches. When a healthy injector closes, its coil releases a voltage spike, often 60 volts or more on port injection systems. A missing spike or a wire stuck at 0 volts tells the PCM the circuit is open or shorted.
Cylinder 11 is found only on V12 engines. Many V12s number one bank 1 to 6 and the other 7 to 12, which puts cylinder 11 fifth from the front on the second bank. Some makers use other systems, so confirm the layout in the service manual.
Many modern V12 engines use direct injection. Those injectors run on high voltage from the engine computer, often 65 volts or more, so a standard noid light test does not apply. Some V12s also use two engine computers, one for each bank.
Symptoms of a Cylinder 11 Injector Fault
With one injector out, the engine runs on one less cylinder. Common signs of a P0211 code include:
- Check engine light on, sometimes flashing
- Misfire code P0311 for cylinder 11
- Rough idle and shaking that gets worse under load
- Hesitation and loss of power
- Raw fuel smell from the exhaust
Common Causes of the P0211 Code
The fault can sit anywhere between the fuse and the PCM driver. These are the usual causes:
- Loose or corroded injector connector. Heat cycles crack the lock tab, and oil or coolant leaks contaminate the pins.
- Chafed or broken control wire. Wires that rub on brackets, the intake or the valve cover can break or short.
- Open injector coil. The fine coil wire inside the injector breaks, and it no longer responds.
- Shorted injector coil. A shorted coil draws too much current and can damage the PCM driver.
- Lost power feed. A break between the injector fuse and this connector cuts the supply.
- Failed PCM injector driver. Less common, and often the result of a shorted injector.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II scan tool that shows live data and misfire counts
- Digital multimeter
- Noid light set for port injection engines
- Back-probe pins and a test light
- Wiring diagram and cylinder layout for your engine
Step-By-Step Diagnosis of the P0211 Code
Start by confirming which cylinder is cylinder 11 on your engine. Then work from the easiest checks to the hardest.
Read All Codes and Freeze Frame
Note every stored code. A P0311 misfire with this code is normal. Several injector codes at once point to a shared power feed.
Inspect the Connector and Wiring
Find the cylinder 11 injector connector. Check that it is fully seated and the lock tab is intact. Look for green corrosion, oil inside the plug and wires that are shiny, flattened or melted where they touch metal.
Check Power at the Connector
Unplug the injector and turn the key on. Probe both pins with a test light grounded to the battery. One pin should light the test light. If neither does, follow the power wire back to the injector fuse or relay.
Use a Noid Light
Plug a noid light into the connector and crank the engine. A steady flash means the PCM is pulsing the cylinder 11 driver. No flash means the control wire is broken or shorted, or the driver has failed. Do not use a noid light on direct injection engines.
Measure Injector Resistance
Measure across the injector terminals. Most high-impedance port injectors read about 11 to 18 ohms at room temperature, and low-impedance types read about 2 to 5 ohms. Compare with the other injectors. An open, a near-zero reading or a value far from the rest means the injector is bad.
Check the Control Wire
With the battery disconnected and the PCM unplugged, check the control wire for under 1 ohm end to end and no short to ground or power.
On port injection engines, you can also swap the injector with a neighbor and clear codes. If the code follows the injector, replace it. If it stays on cylinder 11, the wiring or PCM is at fault.
How to Fix the P0211 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Reseat or replace the connector if it is loose, cracked or corroded. A new pigtail is cheap and lasts longer than cleaning a brittle one.
- Repair damaged wiring with solder and heat shrink tubing, then secure it away from heat and sharp edges.
- Replace the cylinder 11 injector if its resistance is out of range or the code follows it after a swap. Use new O-rings and lube them with clean engine oil.
- Fix oil and coolant leaks that soak the injector wiring, such as a leaking valve cover gasket.
- Repair or replace the PCM only after the wiring and injector test good. Many PCMs need programming after replacement.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the injector before checking power and the noid light signal
- Clearing the P0311 misfire and ignoring the injector circuit code
- Fitting a new PCM without checking for a shorted injector that will damage it again
- Using a standard noid light on a direct injection engine
What Repairs Cost
The cost to fix a P0211 code depends on the cause. Rear injectors under the intake add labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Connector or pigtail | $15 to $40 | $100 to $250 |
| Wiring repair | $10 to $30 | $100 to $350 |
| Port fuel injector | $40 to $150 | $150 to $500 |
| Direct injection injector | $100 to $400 | $350 to $1,000 |
| PCM repair or replacement | $200 to $800 | $500 to $1,500 |
Is It Safe to Drive with a P0211 Code?
It is best to avoid it. The misfire sends unburned fuel and air through the exhaust, which can overheat the catalytic converter and ruin it. A new converter costs far more than most injector circuit repairs.
If the check engine light flashes, slow down and stop driving as soon as it is safe. If it is steady, drive gently and only as far as a repair shop.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0200 | Injector Circuit Malfunction |
| P0311 | Cylinder 11 Misfire Detected |
| P0291 | Cylinder 11 Injector Circuit Low |
| P0292 | Cylinder 11 Injector Circuit High |
| P0293 | Cylinder 11 Contribution/Balance Fault |
| P0300 | Random/Multiple Cylinder Misfire Detected |
Getting Cylinder 11 Firing Again
A P0211 code means the PCM found an electrical fault in the cylinder 11 injector circuit. Loose connectors, damaged wiring and failed injectors cause most cases, and a failed PCM driver is the least likely cause.
- Confirm which cylinder is cylinder 11 on your engine.
- Inspect the connector and wiring for heat damage and oil.
- Check power and use a noid light on port injection engines.
- Measure injector resistance and compare it with the others.
Frequently Asked Questions
Which Engines Can Set the P0211 Code?
Only V12 engines. Examples include V12 engines from BMW, Mercedes-Benz, Ferrari, Lamborghini, Aston Martin and Rolls-Royce. If a scan tool shows this code on a smaller engine, suspect a scan tool error or a PCM that does not match the vehicle.
Do V12 Engines Have Two Engine Computers?
Some do. Several V12 designs use one engine control unit per bank, with one acting as the main unit. If both computers are fitted, an injector code on cylinder 11 usually points to the unit that runs that bank. A dealer-level scan tool helps sort this out.
What Is the Difference Between This Code and P0291?
This code is a general circuit fault for cylinder 11. P0291 and P0292 say more about what the PCM saw, a voltage that is too low or too high. Some vehicles set the general code, and others set the low or high version for the same fault.