P0562 Code: Meaning, Symptoms, Causes & Fixes

A battery light, dim headlights and slow cranking usually point to a charging problem. A P0562 code means the engine computer saw system voltage drop below its expected range.

This guide explains how to test the battery and charging system, and how to find a bad connection that lowers voltage.

P0562 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
5Vehicle speed, idle control and auxiliary inputsThe fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control.
62Specific faultSystem Voltage Low

What the P0562 Code Means

The SAE J2012 standard defines the P0562 code as System Voltage Low. The powertrain control module (PCM) watches system voltage, which is the voltage on its power feed from the battery and charging system. With the engine off, a healthy battery reads about 12.4 to 12.7 volts. With the engine running, most charging systems hold about 13.5 to 14.7 volts.

On many newer vehicles, the PCM or body control module also controls the alternator output. That means a wiring fault, a bad battery sensor or a PCM problem can affect voltage as well as the alternator itself.

Many PCMs set this code when voltage falls below about 10 to 11 volts for a period of time with the engine running, though the exact value varies. A charging system that is not keeping up, a weak battery or high resistance in the PCM feed are the usual reasons.

Symptoms of Low System Voltage

Voltage faults often cause several warnings at once. Common signs of a P0562 code include:

  • Check engine light on
  • Battery or charging warning light
  • Dim or flickering lights
  • Slow cranking or no start
  • Several warning lights or modules acting strangely
  • Stalling or rough running

If the battery light is on while driving, the alternator may not be charging at all. The vehicle will run on battery power until the battery is drained.

Most Common Causes of the P0562 Code

These are the usual causes:

  1. Failing alternator. The most common cause with the engine running.
  2. Weak or failing battery. It cannot hold a charge.
  3. Loose or corroded battery terminals. Resistance lowers the voltage.
  4. Broken or slipping belt. The alternator does not turn properly.
  5. Bad ground strap. Lowers voltage across the system.
  6. Parasitic draw. Something drains the battery with the engine off.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • Digital multimeter
  • Battery load tester or conductance tester
  • OBD-II scan tool that shows system voltage
  • Wire brush and battery terminal cleaner
  • Wiring diagram for your vehicle

How to Diagnose the P0562 Code

Start with the battery and its connections. They cause many voltage codes and are cheap to fix.

Test Battery Voltage

With the engine off, measure battery voltage. About 12.6 volts is fully charged, and below 12.2 volts is low. Charge the battery and have it load tested.

Test Charging Voltage

Start the engine and measure voltage at the battery. About 13.5 to 14.7 volts is normal. If it stays close to battery voltage, the alternator is not charging.

Check the Alternator Circuit

Check the alternator output cable from the alternator to the battery, and its fuse or fusible link. Do a voltage drop test from the alternator output terminal to the battery positive post with the engine running and loads on. More than about 0.5 volt points to a bad cable or connection.

Check the alternator connector and the belt.

Check for a Parasitic Draw

If the battery keeps going flat overnight, measure current draw with the vehicle off and asleep. Most vehicles draw less than about 50 milliamps once the modules sleep.

How to Fix the P0562 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Replace or repair the alternator.
  • Replace a weak battery.
  • Clean and tighten the terminals.
  • Replace a broken or worn belt.
  • Repair the alternator output cable or fuse.
  • Fix a parasitic draw.

Charge the battery fully before testing a new alternator. An alternator is not designed to recharge a dead battery quickly, and doing so can shorten its life.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the battery when the alternator is not charging
  • Jump starting repeatedly without fixing the cause
  • Ignoring a blown alternator fuse

Typical Repair Costs

The cost to fix a P0562 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Battery terminal cleaning$5 to $10$25 to $50
Battery$100 to $250$150 to $350
Alternator$120 to $400$300 to $800
Serpentine belt$20 to $60$75 to $200
Ground strap or wiring repair$10 to $40$100 to $300

An alternator is the most common repair. Many parts stores test batteries and alternators for free.

Can You Drive with a P0562 Code?

Be careful. Charging problems can leave you stranded when the battery runs flat, and very low or very high voltage can make the engine stall or damage electronics.

If the battery light is on or voltage is high, drive only as far as needed and turn off unneeded electrical loads. If the engine begins to stall or warning lights pile up, pull over safely.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0560System Voltage Malfunction
P0561System Voltage Unstable
P0563System Voltage High
P0620Generator Control Circuit Malfunction
P0622Generator Field F Control Circuit Malfunction

Fixing Low System Voltage

A P0562 code means system voltage dropped too low. Failing alternators, weak batteries and corroded terminals cause most cases.

  • Test battery voltage.
  • Test charging voltage with the engine running.
  • Check the alternator cable and belt.
  • Check for a parasitic draw.

Frequently Asked Questions

Can I Drive with the P0562 Code?

Only a short distance. If the alternator is not charging, the vehicle runs on battery power until the battery is drained, then stalls. Turn off loads such as the A/C and head straight for a repair shop.

What Voltage Should My Car Have?

With the engine off, a fully charged battery reads about 12.6 volts. With the engine running, most charging systems hold about 13.5 to 14.7 volts. Some newer vehicles let voltage drop closer to 12.5 volts at times to save fuel, which can be normal.

Can a Bad Battery Cause a Voltage Code?

Yes. A battery with a shorted cell or high internal resistance can drag voltage down or make it unstable. Have it load tested, since a battery can show good voltage at rest and still fail under load.

Can I Test the Alternator Myself?

Yes. With the engine running, measure voltage at the battery. Turn on the headlights, blower and rear defroster. Voltage should stay above about 13 volts. A reading near battery voltage means the alternator is not charging.

Do I Need to Register a New Battery?

Some vehicles, including many BMW, Audi, Volkswagen and Ford models, need a new battery registered with a scan tool. Without it, the charging system may overcharge or undercharge the new battery.

Where Are the Main Ground Straps?

Most vehicles have a heavy cable from the battery negative post to the engine block or transmission, and another from the engine or battery to the body. Some also have a strap from the engine to the firewall. Corrosion where they bolt on is common, especially in areas that use road salt.

Why Do Several Warning Lights Appear at Once?

Modules need a steady supply voltage to work. When voltage drops or jumps, several of them can report faults at the same time, and the dash fills with warnings. Fix the voltage problem first, then clear the codes. Most of the other warnings usually go away.

Can Aftermarket Accessories Cause Voltage Codes?

Yes. A large stereo amplifier, extra lights or a winch can draw more current than the charging system was built for, and poor wiring for them can create a bad ground or a parasitic draw. Check any accessory wiring if the problem started after it was installed.