On many vehicles, the transmission range sensor sends a voltage that changes with the shifter position. A P0708 code means that signal is higher than its allowed range.
This guide explains what the range sensor does, why it goes out of adjustment and how to test it.
P0708 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 7 | Transmission | The fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch. |
| 08 | Specific fault | Transmission Range Sensor Circuit High Input |
What the P0708 Code Means
The SAE J2012 standard defines the P0708 code as Transmission Range Sensor Circuit High Input. The transmission range sensor (TRS), also called the neutral safety switch or PRNDL switch, tells the computer which gear the shifter is in. It usually mounts on the side of the transmission at the shift lever shaft. On some transmissions, it sits inside the case on the valve body.
Some range sensors use several switch contacts, and the computer reads which ones are closed. Others send a single voltage that changes with each position. The computer uses the signal to allow starting only in park or neutral, to turn on the reverse lights, to show the gear on the dash and to choose shift patterns.
Because the range sensor moves every time you shift, its contacts wear, and dirt or water can get inside. A sensor that is slightly out of adjustment can also read between two positions.
High input means the signal voltage rose above the highest value a working transmission range sensor should ever send. That usually points to an open ground, a signal wire touching the reference or another voltage source, or a failed sensor.
Symptoms of a Transmission Range Sensor Fault
Range sensor problems show up in several ways. Common signs of a P0708 code include:
- Engine will not crank in park or neutral
- Engine cranks in a drive gear
- Wrong gear shown on the dash
- Reverse lights not working
- Harsh shifts or limp mode
- Check engine light on
If the engine starts in a drive gear, stop driving and get it fixed. The vehicle could lurch when started. Moving the shifter slightly while holding the brake, until the engine cranks, is a common sign of a worn or misadjusted sensor.
What Causes the P0708 Code?
High input faults almost always come from an electrical problem:
- Open sensor ground. Without a ground, the signal floats up toward the reference.
- Signal wire shorted to the 5-volt reference. Damaged insulation lets the wires touch.
- Signal wire shorted to battery voltage. Less common, but possible.
- Corroded connector. Resistance on the ground pin raises the signal.
- Failed transmission range sensor. An internal fault locks the output high.
- PCM fault. Rare.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II or transmission scan tool that shows transmission range
- Digital multimeter
- Wiring diagram for your transmission
- Range sensor alignment tool or drill bit
- Contact cleaner
How to Track Down the P0708 Code
Set the parking brake and keep your foot on the brake whenever you move the shifter with the engine running.
Check Live Data
With the key on and your foot on the brake, move the shifter through each position and watch the transmission range in live data. It should match the shifter exactly. A reading that is missing, wrong or flickers confirms a problem.
Test the Ground First
Back-probe the sensor ground with the key on and measure against the battery negative post. It should read close to 0 volts, ideally under 0.1 volt. A higher reading means a poor ground.
Check for a Short to Voltage
Unplug the transmission range sensor with the key on and watch the signal in live data. If it stays high with the sensor unplugged, the signal wire is shorted to the reference or another voltage source. If it changes, the sensor itself is likely at fault.
Check the Sensor Contacts
Unplug the sensor and test continuity or resistance across its pins in each shifter position, using the chart in your service manual. A contact that does not close, or one that reads high resistance, means the sensor is worn.
Repairs That Fix the P0708 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Adjust the range sensor to the service manual specification.
- Replace a worn range sensor.
- Adjust or replace the shift cable.
- Clean and seal a wet connector.
- Repair damaged wiring.
After replacing the sensor, set its position with the alignment tool before you tighten it. Then check that the engine cranks only in park and neutral, and that the reverse lights work only in reverse.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the sensor without testing the ground first
- Overlooking a short to voltage inside a wiring bundle
- Installing a new sensor without aligning it
- Ignoring a stretched shift cable
What Repairs Cost
The cost to fix a P0708 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Connector cleaning or repair | $10 to $30 | $75 to $250 |
| Wiring repair | $10 to $40 | $100 to $300 |
| Range sensor adjustment | $0 | $50 to $120 |
| Transmission range sensor | $40 to $200 | $150 to $450 |
| Shift cable | $30 to $150 | $150 to $350 |
External range sensors are usually easy to reach. Internal ones need the pan dropped, which adds labor.
Is It Safe to Keep Driving with a P0708 Code?
Be careful. If the engine starts in a drive gear, it is not safe to drive, because the vehicle could move when you start it.
If the engine will not crank in park, try neutral. Many range sensor faults also cause harsh shifts or limp mode, so drive gently until it is fixed.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| P0706 | Transmission Range Sensor Circuit Range/Performance |
| P0707 | Transmission Range Sensor Circuit Low Input |
| P0709 | Transmission Range Sensor Circuit Intermittent |
| P0700 | Transmission Control System Malfunction |
| P0850 | Park/Neutral Switch Input Circuit |
Fixing the Transmission Range Sensor
A P0708 code means the transmission range sensor voltage is too high. Lost grounds, shorts to voltage and failed sensors cause most cases.
- Watch the range in live data as you shift.
- Check the sensor adjustment and shift cable.
- Test the sensor contacts.
- Adjust or replace the sensor.
Frequently Asked Questions
Can a Bad Ground Cause the P0708 Code?
Yes, and it is one of the most common causes. Without a solid ground, the transmission range sensor signal floats up toward the reference voltage. Check the ground pin, the wire and the ground connections at the engine and PCM.
Why Does My Car Start Only in Neutral?
A worn or misadjusted range sensor may not close the park contact, while the neutral contact still works. Moving the shifter slightly in park may also help it crank. Adjusting or replacing the sensor fixes it.
Can a Bad Range Sensor Cause Harsh Shifting?
Yes. If the computer is not sure which gear is selected, it may use a backup shift strategy or limp mode. Shifts can be harsh or delayed until the sensor is fixed.
Can Low Transmission Fluid Cause Sensor Codes?
Sometimes. Low fluid makes the transmission slip and run hot, which can upset speed and temperature readings and set range codes. Check the fluid level with the procedure in your service manual before you replace a sensor.
Does the Transmission Need a Relearn After a Sensor Repair?
Some do. Many modern transmissions store learned shift data, and a few need a relearn or a reset after a sensor or wiring repair. Check the service manual, especially if shifts feel odd after the fix.
Where Is the Transmission Computer?
On some vehicles, the PCM controls the transmission. On others, a separate transmission control module (TCM) sits under the dash, in the engine bay or bolted inside the transmission. Your service manual shows which one your vehicle uses.
Can I Check the Transmission Fluid Myself?
On many older vehicles, yes, with the dipstick and the engine running in park at operating temperature. Many newer transmissions have no dipstick and are checked at a fill plug with the fluid at a set temperature, often with a scan tool to read it. Follow the procedure for your transmission.
Should I Fix Electrical Codes Before Mechanical Ones?
Yes. A sensor or wiring fault can make the computer shift badly, use limp mode or misjudge gear ratio, which may set other codes that look mechanical. Fix the electrical faults first, clear the codes and see which ones come back.