A diesel that stalls or stumbles for a moment and then runs again may have a loose fuel metering connection. A P0260 code means the engine computer saw the injection pump fuel metering control B circuit drop out for short moments.
This guide explains how intermittent faults set, what causes them and how to catch one while it happens.
P0260 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 2 | Fuel and air metering | The fault involves fuel and air metering, such as injectors, the fuel pump, throttle sensors or boost control. |
| 60 | Specific fault | Injection Pump Fuel Metering Control “B” Intermittent (Cam/Rotor/Injector) |
What the P0260 Code Means
The SAE J2012 standard defines the P0260 code as Injection Pump Fuel Metering Control “B” Intermittent (Cam/Rotor/Injector). Fuel metering control B is a second metering control. Some pumps use two, for example one for quantity and one for timing or for each pump element, and some manufacturers use the B circuit for a related actuator. Check your service manual to see what control B is on your engine.
The powertrain control module (PCM) or engine control module pulses the actuator to open or close a fuel passage. By changing the on-time, it changes how much fuel reaches the high-pressure side of the pump, which sets rail pressure or fuel quantity.
The PCM watches the actuator current and the result, such as rail pressure. When the circuit or the result does not match its command, it sets a fuel metering code.
Intermittent means the fuel metering control B circuit dropped out or misbehaved for short moments. The fault may last only a fraction of a second, so the circuit often tests fine when parked.
Symptoms of a Bad Fuel Metering Control B
Because this control sets fuel delivery, symptoms can be severe. Common signs of a P0260 code include:
- Engine cranks but will not start
- Stalling at idle or while driving
- Low power or limp mode
- Surging or unstable idle
- Black or white smoke
- Check engine light on
On common rail engines, a metering valve stuck open can push rail pressure too high, while one stuck closed starves the engine. Both can cause stalling, so the symptoms alone do not tell you which way the part failed.
What Causes the P0260 Code?
Anything that breaks the circuit for an instant can set this code:
- Loose connector. A connector not fully locked loses contact.
- Spread or corroded terminals. Weak pins lose grip as they heat up.
- Chafed wiring. Insulation wears through where wires rub.
- Broken wire inside the insulation. The copper separates only when flexed.
- Failing fuel metering control B. An internal fault comes and goes with heat.
Tools You Will Need
You can do most of this testing at home with basic tools:
- Scan tool that shows desired and actual rail pressure
- Digital multimeter
- Low-pressure fuel gauge for the lift pump
- New fuel filter and water separator kit
- Wiring diagram for your engine
How to Track Down the P0260 Code
Diesel fuel systems can hold very high pressure. Follow the service manual to relieve pressure before you open any high-pressure line, and never check for leaks with your hand.
Check Live Data and Command the Part
Look at desired and actual rail pressure, or fuel quantity, along with the actuator current or duty cycle. With the engine idling, desired and actual values should track closely.
Wiggle Test the Circuit
With the engine running or the fuel metering control B commanded on, gently wiggle the connector and wiring one section at a time while you watch live data. A sudden change or a new code marks the bad spot.
Inspect the Connector
Turn the engine off and unplug the connector. Look for corrosion, spread pins, a broken lock and water inside.
Check for Related Codes
Rail pressure codes such as P0087 (too low) and P0088 (too high), lift pump codes and filter warnings often show up with this one. They help tell a supply problem from an actuator problem.
How to Fix the P0260 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Repair the connector or wiring at the pump, where heat and vibration are high.
- Replace the fuel filter and drain water from the separator.
- Repair a weak lift pump or fuel supply leak.
- Replace the fuel metering actuator B if it fails resistance tests or sticks. On many pumps it bolts on separately.
- Replace the injection pump only if it is worn or contaminated.
If you find metal in the fuel filter, the high-pressure pump may be failing and spreading debris through the system. In that case, the injectors and rails may also need attention, so a diesel specialist should inspect it.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing parts when the circuit tests fine at rest
- Not wiggle testing the wiring with the engine running
- Replacing the injection pump before checking supply pressure and the filter
- Ignoring water in the fuel, which damages pumps and actuators
Typical Repair Costs
The cost to fix a P0260 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Fuel filter | $20 to $80 | $80 to $200 |
| Wiring or connector repair | $10 to $40 | $100 to $300 |
| Fuel control actuator | $80 to $300 | $250 to $600 |
| Lift pump | $100 to $400 | $300 to $800 |
| High-pressure injection pump | $800 to $3,000 | $2,000 to $5,000 |
On many common rail diesels, the fuel control actuator can be replaced on its own without removing the pump. That makes it one of the cheaper repairs for this code, as long as the pump itself is healthy.
Is It Safe to Keep Driving with a P0260 Code?
It is risky. A fuel metering fault can stall the engine without warning, which may cut power steering and brake assist on some diesels.
If the engine runs normally, drive gently to a repair shop. If it stalls, surges or will not hold idle, have it towed.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0256 | Injection Pump Fuel Metering Control “B” Malfunction (Cam/Rotor/Injector) |
| P0257 | Injection Pump Fuel Metering Control “B” Range/Performance (Cam/Rotor/Injector) |
| P0258 | Injection Pump Fuel Metering Control “B” Low (Cam/Rotor/Injector) |
| P0259 | Injection Pump Fuel Metering Control “B” High (Cam/Rotor/Injector) |
| P0087 | Fuel Rail/System Pressure Too Low |
| P0088 | Fuel Rail/System Pressure Too High |
Fixing Fuel Metering Control B
A P0260 code means the fuel metering control B circuit drops out for short moments. Loose connectors and chafed wiring cause most cases.
- Compare desired and actual rail pressure.
- Inspect the connector and wiring at the pump.
- Measure the actuator resistance.
- Check lift pump pressure and the fuel filter.
Frequently Asked Questions
Why Does the P0260 Code Come and Go?
Intermittent faults often appear only with heat, vibration or moisture. The connector on the pump sits in a hot, shaking spot, so worn pins and chafed wires are common. Wiggle testing while you watch live data is the best way to catch it.
Which Engines Set This Code?
It is mostly a diesel code. It is common on Cummins engines in Ram trucks, where the fuel control actuator sits on the high-pressure pump, and on older diesels with electronic rotary pumps such as GM’s 6.5L. Some other diesels use it for their metering valve.
What Is a Fuel Control Actuator?
It is an electric valve on the inlet side of a common rail high-pressure pump. The engine computer opens and closes it to control how much fuel the pump compresses, which sets rail pressure. Cummins calls it the FCA, and other makers use names such as inlet metering valve.
Can Bad Fuel Cause Fuel Metering Codes?
Yes. Water, gasoline contamination and debris can make the metering actuator stick and wear the pump. Always use clean diesel from a busy station, drain the water separator regularly and replace the fuel filter on schedule.
How Long Does the Repair Take?
Replacing a bolt-on fuel control actuator often takes one to two hours. Wiring repairs can be quicker. A high-pressure pump replacement can take most of a day and may need the fuel system cleaned if the old pump shed metal.