Diesel engines watch exhaust back pressure to control the turbocharger and warm up the engine. A P0470 code means the engine computer found a problem in the exhaust pressure sensor circuit.
This guide explains what the sensor does, why its sensing tube clogs with soot and how to test it.
P0470 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 4 | Auxiliary emission controls | The fault involves emission control systems such as EGR, secondary air, EVAP or the catalytic converter. |
| 70 | Specific fault | Exhaust Pressure Sensor Malfunction |
What the P0470 Code Means
The SAE J2012 standard defines the P0470 code as Exhaust Pressure Sensor Malfunction. The exhaust pressure sensor, often called the exhaust back pressure (EBP) sensor, measures pressure in the exhaust manifold before the turbocharger. It is mostly found on diesel engines, such as Ford Power Stroke and Navistar engines. A metal tube carries exhaust pressure from the manifold to the sensor.
The sensor gets a 5-volt reference and a ground from the powertrain control module (PCM), and sends back a signal that rises with exhaust pressure. The PCM uses it to control the exhaust back pressure valve or the turbo’s variable vanes, and on some engines to help control EGR.
With the engine off, the sensor should read close to barometric pressure, because the exhaust is open to the air. The PCM often compares it with the barometric or manifold pressure sensor at key-on to check that it reads correctly.
This is the general circuit code for the exhaust pressure sensor. The PCM saw a signal it could not accept, such as one that is missing, out of range or does not match a related input, but the code does not say whether the signal was too low or too high.
Symptoms of an Exhaust Pressure Sensor Fault
Symptoms depend on how the engine uses the reading. Common signs of a P0470 code include:
- Check engine light on
- Low power or slow turbo response
- Rough or slow warm-up in cold weather
- Turbo noise that sounds different from normal
- EGR codes on some engines
Many engines switch to a default value and run with less power. On some engines, the PCM disables the warm-up strategy or limits turbo boost to protect the engine.
Most Common Causes of the P0470 Code
A general circuit fault can come from anywhere in the circuit. These are the usual causes:
- Loose or corroded connector. Moisture and heat attack the pins.
- Damaged wiring. Wires can chafe, break or melt near hot or moving parts.
- Failed exhaust pressure sensor. Internal wear or damage stops it from reporting correctly.
- Problem with the 5-volt reference or ground. Shared circuits can affect several sensors at once.
- PCM fault. Rare.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II or diesel scan tool that shows exhaust pressure
- Digital multimeter with back-probe pins
- Wiring diagram for your engine
- Small wire or brush to clear the sensor tube
- Replacement sensor tube and gaskets
Step-By-Step Diagnosis of the P0470 Code
Let the engine cool before you touch the exhaust manifold or sensor tube.
Check Live Data
With the key on and engine off, compare the exhaust pressure reading with barometric pressure. With the engine running, it should rise as the engine revs. A reading stuck near 0 or 5 volts confirms a circuit fault.
Inspect the Connector and Wiring
Find the exhaust pressure sensor and check that the connector is fully seated and locked. Look for corrosion, bent pins and wiring that rubs on brackets or hot parts.
Test Reference, Ground and Signal
Back-probe the connector with the key on. The reference should read close to 5 volts, the ground close to 0 volts, and the signal should match the value your service manual lists. Any wire that fails tells you where to look next.
How to Fix the P0470 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Clear or replace a clogged sensor tube.
- Repair the connector or wiring.
- Replace the exhaust pressure sensor if it reads wrong.
- Repair exhaust leaks before the turbo.
- Free sticking turbo vanes or a stuck back pressure valve.
On Ford 6.0L Power Stroke engines, many technicians replace the sensor tube along with the sensor, since soot and moisture in the tube often cause repeat failures. Route the new tube so it slopes down toward the manifold and drains.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the sensor before checking the connector and wiring
- Ignoring other codes that share the same reference or ground
- Replacing the sensor without clearing the tube
- Ignoring an exhaust leak before the turbo
What Repairs Cost
The cost to fix a P0470 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Sensor tube cleaning or replacement | $10 to $50 | $75 to $200 |
| Connector or wiring repair | $10 to $30 | $100 to $300 |
| Exhaust pressure sensor | $40 to $150 | $150 to $350 |
| Turbo vane cleaning | $20 | $300 to $800 |
Most cases cost little once the tube is cleared. Turbo work costs more and is only needed if the vanes or the back pressure valve stick.
Is It Safe to Drive with a P0470 Code?
Usually, yes, for short trips. The engine may run with less power and slower turbo response, which makes merging and towing harder.
Avoid heavy loads until it is fixed. If the turbo vanes or back pressure valve are stuck, high exhaust pressure can harm the engine and turbo over time.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0471 | Exhaust Pressure Sensor Range/Performance |
| P0472 | Exhaust Pressure Sensor Low |
| P0473 | Exhaust Pressure Sensor High |
| P0474 | Exhaust Pressure Sensor Intermittent |
| P0475 | Exhaust Pressure Control Valve Malfunction |
| P0299 | Turbo/Super Charger Underboost |
Fixing the Exhaust Pressure Sensor
A P0470 code means the PCM found a fault in the exhaust pressure sensor circuit. Corroded connectors, damaged wiring and failed sensors cause most cases.
- Check the reading in live data.
- Inspect the connector and wiring.
- Test reference, ground and signal.
- Replace the sensor only after the wiring tests good.
Frequently Asked Questions
Do Gasoline Engines Have an Exhaust Pressure Sensor?
Most do not. The sensor is mostly used on diesel engines, especially Ford Power Stroke and Navistar engines, to control the turbo and the warm-up strategy. Some diesels use it as part of EGR and particulate filter control as well.
Where Is the Exhaust Pressure Sensor?
On many diesels, it mounts on a bracket on the engine, with a metal tube running to the exhaust manifold. On Ford 6.0L engines, it sits near the back of the engine, under the intake area. Your service manual shows the exact location.
Is the Exhaust Pressure Sensor the Same as the DPF Pressure Sensor?
No. The exhaust pressure sensor reads pressure before the turbo. The DPF differential pressure sensor reads the difference across the particulate filter and sets different codes.
Can a Bad Exhaust Pressure Sensor Cause Low Power?
Yes. If the PCM cannot trust the reading, it may limit turbo boost or switch to a default strategy. Fixing the sensor or tube often brings full power back.
What Should the Sensor Read at Key-On?
With the engine off, it should read close to barometric pressure, about 14.7 psi at sea level. It reads less at high altitude. The PCM compares the two to check the sensor.
Why Does the Sensor Tube Clog?
Diesel exhaust carries soot and moisture. Over time, soot packs into the narrow tube, especially if it has low spots where moisture collects. Short trips and lots of idling make it worse. Clearing or replacing the tube, and routing it so it drains, keeps it open longer.
Should I Buy an Original Sensor?
For this sensor, many owners and technicians prefer the original equipment part. Some low-cost sensors read slightly off, which can set a range code or upset turbo control. Check that the part number matches your engine.