An engine that idles too fast wastes fuel and makes the car pull at stop lights. A P0507 code means the engine computer found that idle speed is higher than its target.
This guide explains what lets extra air into the engine, how to find a vacuum leak and how to fix a high idle.
P0507 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 5 | Vehicle speed, idle control and auxiliary inputs | The fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control. |
| 07 | Specific fault | Idle Control System RPM Higher Than Expected |
What the P0507 Code Means
The SAE J2012 standard defines the P0507 code as Idle Control System RPM Higher Than Expected. The powertrain control module (PCM) holds the engine at a target idle speed, usually somewhere between about 600 and 900 rpm on a warm engine, and higher when cold. It raises the target when loads such as the A/C, power steering or electrical system pull on the engine.
On older vehicles, an idle air control (IAC) valve on the throttle body lets a small amount of air bypass the closed throttle plate. On most newer vehicles with electronic throttle control, the throttle body motor opens the throttle plate slightly to control idle, and there is no separate IAC valve.
The code usually sets when idle stays above the target, often by about 200 rpm or more, even though the PCM is trying to lower it. In most cases, extra air is getting into the engine past the throttle.
Symptoms of a High Idle
Idle problems are easy to feel at a stop. Common signs of a P0507 code include:
- Check engine light on
- Idle higher than normal
- Car pulling or creeping at stops
- Harsh shift into drive
- Hissing noise from the engine bay
A high idle often comes with a lean condition, so lean codes such as P0171 may show up too.
Most Common Causes of the P0507 Code
These are the usual causes:
- Vacuum leak. Cracked hoses or a leaking intake gasket. This is the most common cause.
- Stuck IAC valve. It lets in too much air.
- Sticking throttle plate. Carbon or a worn cable holds it open.
- Faulty PCV valve. A stuck-open valve adds extra air.
- Leaking brake booster. Its vacuum hose or diaphragm leaks.
- Needs an idle relearn. After cleaning or a battery disconnect.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II scan tool that shows idle speed, target idle and IAC or throttle position
- Throttle body cleaner and a soft brush
- Smoke machine or carburetor cleaner for finding vacuum leaks
- Digital multimeter
- Scan tool or procedure for an idle relearn
How to Track Down the P0507 Code
Start with the engine fully warm, since cold idle speeds are higher by design.
Check Fuel Trim
With the engine warm, look at short and long term fuel trim at idle. High positive trim at idle that drops at higher rpm points to a vacuum leak.
Find the Vacuum Leak
Listen for hissing and check every vacuum hose. Use a smoke machine for the best results. Spraying carburetor cleaner near suspect spots works too. If the idle changes, you have found the leak.
Check the Brake Booster
With the engine idling, pinch the booster vacuum hose briefly or press the brake pedal and listen. If the idle drops a lot or the hiss changes, the booster or its hose may be leaking.
A leaking booster can also make the brake pedal feel hard.
Check the Throttle and IAC
Make sure the throttle plate closes fully and the cable, if fitted, is not sticking. Clean the throttle body and IAC passage, and check that the IAC valve closes when commanded.
Repairs That Clear the P0507 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Repair vacuum leaks.
- Replace a faulty PCV valve.
- Clean or replace a stuck IAC valve.
- Free a sticking throttle.
- Replace a leaking brake booster or hose.
- Run an idle relearn.
After fixing a vacuum leak, clear the codes and run an idle relearn if needed. The PCM may take a few drives to reset its fuel trim and idle learning.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the IAC valve when a hose is cracked
- Missing a leaking brake booster
- Skipping the idle relearn
What Repairs Cost
The cost to fix a P0507 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Throttle body cleaning | $10 | $75 to $150 |
| Vacuum leak repair | $5 to $50 | $100 to $300 |
| IAC valve | $40 to $150 | $150 to $350 |
| PCV valve or hose | $5 to $30 | $50 to $150 |
| Electronic throttle body | $100 to $400 | $300 to $700 |
Vacuum hoses and PCV valves are cheap. A brake booster or intake gasket costs more, mostly in labor.
Is It Safe to Keep Driving with a P0507 Code?
Usually, yes, but be careful. A low idle can make the engine stall at stops or when you turn on the A/C, which leaves you without power assist for steering and brakes.
A high idle can make the vehicle creep forward at stops and wear the brakes. Get it fixed soon, and keep a firm foot on the brake.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0505 | Idle Control System Malfunction |
| P0506 | Idle Control System RPM Lower Than Expected |
| P0171 | System Too Lean (Bank 1) |
| P0121 | Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance Problem |
| P0510 | Closed Throttle Position Switch Malfunction |
Bringing a High Idle Down
A P0507 code means idle speed is higher than the PCM wants. Vacuum leaks, stuck IAC valves and faulty PCV valves cause most cases.
- Check fuel trim at idle.
- Find vacuum leaks with smoke.
- Check the brake booster.
- Check the throttle and IAC valve.
Frequently Asked Questions
Can a Vacuum Leak Cause the P0507 Code?
Yes, and it is the most common cause. Extra air that leaks into the intake raises idle speed, and the PCM cannot close the throttle enough to bring it down. Find and fix the leak.
Can a Dirty Throttle Body Cause Idle Problems?
Yes. Carbon builds up around the throttle plate and in the IAC passage over time. It restricts the small amount of air the engine needs at idle. Cleaning the throttle body is one of the most common fixes for idle codes.
Do I Need an Idle Relearn After Cleaning?
Often, yes. Many vehicles learn how much air they need at idle. After you clean the throttle body or disconnect the battery, they may idle oddly until they relearn. Some do it on their own after a drive, while others need a scan tool procedure.
What Is a Normal Idle Speed?
On most warm engines, idle is somewhere between about 600 and 900 rpm in park or neutral. It is higher on a cold engine and rises when the A/C is on. Check the target idle in live data, since the PCM shows what it is trying to reach.
Can a Vacuum Leak Cause Idle Codes?
Yes. A vacuum leak lets extra air into the engine that the PCM does not control. The idle may rise, or the engine may run lean and rough. Spraying carburetor cleaner around suspect hoses, or using a smoke machine, helps find the leak.
Can a Weak Battery or Alternator Affect Idle?
It can. When the charging system struggles, the alternator puts more load on the engine, and the PCM raises idle to keep up. A failing alternator can drag idle down or make it hunt. Check battery voltage at idle, which should usually be about 13.5 to 14.7 volts with the engine running.
Should I Disconnect the Battery to Reset Idle?
It can clear the learned idle values, but it is not a fix on its own. Many vehicles idle poorly until they relearn, and some need a scan tool procedure. Fix the cause first, such as a dirty throttle body or a vacuum leak, then let the PCM relearn.