P0550 Code: Meaning, Symptoms, Causes & Fixes

Turning the wheel at a stop puts a heavy load on the engine, so the engine computer watches power steering pressure and raises idle to match. A P0550 code means the engine computer found a problem in the power steering pressure sensor circuit.

This guide explains what the sensor or switch does, why it leaks and fails and how to test it.

P0550 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
5Vehicle speed, idle control and auxiliary inputsThe fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control.
50Specific faultPower Steering Pressure Sensor Circuit Malfunction

What the P0550 Code Means

The SAE J2012 standard defines the P0550 code as Power Steering Pressure Sensor Circuit Malfunction. The power steering pressure (PSP) sensor or switch threads into the high-pressure power steering line or the pump. On some vehicles, it is a simple switch that closes at high pressure. On others, it is a sensor that sends a voltage that rises with pressure.

The powertrain control module (PCM) uses the signal to raise idle speed before the power steering load can drag the engine down. Without it, the idle may dip or the engine may stall when you turn the wheel sharply at a stop or while parking.

Vehicles with electric power steering do not have a hydraulic pump, so they use a different system and usually do not set these codes.

This is the general circuit code for the power steering pressure sensor. The PCM saw a signal it could not accept, such as one that is missing, out of range or does not match a related input, but the code does not say whether the signal was too low or too high.

Symptoms of a Power Steering Pressure Sensor Fault

Most symptoms show up at low speed. Common signs of a P0550 code include:

  • Check engine light on
  • Idle dropping when you turn the wheel at a stop
  • Stalling while parking
  • Power steering fluid leaking at the sensor
  • High idle on some vehicles

A leaking sensor is common. If you see fluid around it or on the connector, the sensor seal has likely failed, and the fluid can cause the electrical fault too.

Most Common Causes of the P0550 Code

A general circuit fault can come from anywhere in the circuit. These are the usual causes:

  1. Loose or corroded connector. Moisture and heat attack the pins.
  2. Damaged wiring. Wires can chafe, break or melt near hot or moving parts.
  3. Failed power steering pressure sensor. Internal wear or damage stops it from reporting correctly.
  4. Problem with the 5-volt reference or ground. Shared circuits can affect several sensors at once.
  5. PCM fault. Rare.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II scan tool that shows power steering pressure or switch status
  • Digital multimeter
  • Wiring diagram for your vehicle
  • Line wrench for the sensor
  • Correct power steering fluid

How to Track Down the P0550 Code

Start with the fluid level and a look for leaks, then test the circuit.

Check Live Data

With the engine idling, watch the power steering pressure sensor or switch status in live data. Turn the wheel toward full lock. The reading should change. A reading stuck near 0 or 5 volts confirms a circuit fault.

Inspect the Connector and Wiring

Find the power steering pressure sensor and check that the connector is fully seated and locked. Look for corrosion, bent pins and wiring that rubs on brackets or hot parts.

Test Reference, Ground and Signal

Back-probe the connector with the key on. The reference should read close to 5 volts, the ground close to 0 volts, and the signal should match the value your service manual lists. Any wire that fails tells you where to look next.

Repairs That Clear the P0550 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Replace a leaking sensor and clean fluid out of the connector.
  • Repair the connector or wiring.
  • Top off the power steering fluid.
  • Repair a worn pump if pressure stays low.
  • Replace the sensor if it fails tests.

Expect a little fluid to leak when you remove the sensor. Have a rag ready, top off the fluid afterward and turn the wheel lock to lock a few times with the engine running to bleed out air.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the sensor before checking the connector and wiring
  • Ignoring other codes that share the same reference or ground
  • Ignoring fluid in the connector
  • Overlooking a low fluid level

Typical Repair Costs

The cost to fix a P0550 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Power steering pressure sensor or switch$15 to $80$100 to $250
Wiring or connector repair$10 to $30$100 to $300
Power steering fluid$10 to $20$30 to $60
Power steering pump$80 to $300$300 to $700

The sensor is usually cheap, and the job takes less than an hour on most vehicles. A pump replacement costs more and is only needed if pressure is truly low.

Is It Safe to Keep Driving with a P0550 Code?

Usually, yes. Steering still works, because the sensor only tells the PCM about the load.

Be careful when parking and at stops, though. The engine may stall when you turn the wheel, and the steering becomes very heavy if it does.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0551Power Steering Pressure Sensor Circuit Range/Performance
P0552Power Steering Pressure Sensor Circuit Low Input
P0553Power Steering Pressure Sensor Circuit High Input
P0554Power Steering Pressure Sensor Circuit Intermittent
P0505Idle Control System Malfunction
P0506Idle Control System RPM Lower Than Expected

Fixing the Power Steering Pressure Sensor

A P0550 code means the PCM found a fault in the power steering pressure sensor circuit. Corroded connectors, damaged wiring and failed sensors cause most cases.

  • Check the reading in live data.
  • Inspect the connector and wiring.
  • Test reference, ground and signal.
  • Replace the sensor only after the wiring tests good.

Frequently Asked Questions

Why Does My Engine Stall When I Turn the Wheel?

Turning the wheel at a stop loads the power steering pump heavily. The PCM raises idle when the sensor reports high pressure. If the sensor fails, the idle may not rise, and the engine can stall.

Where Is the Power Steering Pressure Sensor?

It is usually on the high-pressure line near the power steering pump or on the pump itself. It has a one, two or three-wire connector, depending on whether it is a switch or a sensor.

Is It a Switch or a Sensor?

It depends on the vehicle. A switch simply turns on at a set pressure. A sensor sends a voltage that rises with pressure. Both do the same job for the PCM.

Do Electric Power Steering Systems Have This Sensor?

No. Electric systems have no hydraulic pump, so they do not use a pressure sensor. They talk to the PCM over the network instead.

Can a Leaking Sensor Damage the Wiring?

Yes. Power steering fluid that leaks into the connector can travel up the wires and cause signal errors. Replace the sensor and clean the connector and wiring.

Can a Bad Sensor Cause a High Idle?

On some vehicles, yes. If the sensor or switch reads high pressure all the time, the PCM keeps raising the idle as if you were turning the wheel. Unplugging a switch-type sensor for a moment with the engine running and watching the idle can help show whether it is stuck.

What Fluid Should I Use?

Use the fluid listed in your owner’s manual or on the reservoir cap. Some systems use automatic transmission fluid, while others need a specific power steering fluid. The wrong fluid can damage seals and cause new leaks, including at the pressure sensor.