Modern vehicles have many computers that share information over a network. A P0600 code means the engine computer found a problem with a serial communication link it uses to talk to other modules or between its own processors.
This guide explains what the code means, what can cause it besides a bad computer and what to check before you replace the module.
P0600 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 6 | Computer and output circuits | The fault involves the engine computer itself or circuits it controls, such as the charging system and warning lamps. |
| 00 | Specific fault | Serial Communication Link Malfunction |
What the P0600 Code Means
The SAE J2012 standard defines the P0600 code as Serial Communication Link Malfunction. The powertrain control module (PCM), also called the engine control module (ECM) on some vehicles, is the computer that runs the engine and often the transmission. It constantly checks its own memory, processors and software while the key is on.
Most internal PCM codes do not mean the computer is dead. Low voltage, poor grounds, a failed software update or water damage can all make a healthy module fail its self-tests. That is why power, ground and software are checked before the module is replaced.
On many vehicles, this code points to a problem on the network between the PCM and modules such as the transmission, ABS or instrument cluster. On some, it means two processors inside the PCM could not communicate. Look for U-codes in other modules, which help show where the break is.
Symptoms of a PCM Internal Fault
Symptoms range from none at all to a vehicle that will not start. Common signs of a P0600 code include:
- Check engine light on
- Engine stalling or not starting
- Limp mode or reduced power
- Harsh or erratic shifting
- Other modules reporting communication codes
Some vehicles run normally with these codes, while others stall or will not start. The symptoms depend on which part of the module failed its test.
Common Causes of the P0600 Code
These are the usual causes:
- Network wiring fault. A broken, shorted or corroded data wire.
- Faulty module on the network. One failed module can disturb the whole network.
- Low or unstable voltage. Modules drop off the network.
- Loose or corroded connector. At the PCM or another module.
- PCM internal fault. Two processors inside cannot talk.
- Aftermarket accessories. Remote starters and alarms tied into data wires.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II scan tool
- Digital multimeter
- Wiring diagram for your vehicle
- Battery charger or maintainer for programming
- Factory or professional programming tool
How to Track Down the P0600 Code
Charge the battery fully and check it before you test anything else. Low voltage causes many false computer codes.
Test the Battery and Charging System
Measure battery voltage with the engine off, then running. Have the battery load tested. A weak battery or charging fault can make the PCM fail its self-tests.
Check PCM Power and Ground
Using the wiring diagram, find the PCM battery feed, ignition feed and ground pins. Check every PCM fuse. With the key on, measure voltage at the feed pins and voltage drop on the grounds. Grounds should read under about 0.1 volt to battery negative.
Scan All Modules
Use a scan tool that can read every module. Note which modules have communication codes, often U-codes, and which ones do not respond at all.
Check the Network Wiring
On CAN networks, measure resistance between the CAN high and CAN low pins at the diagnostic connector with the battery disconnected. About 60 ohms is typical for a network with two 120-ohm terminating resistors. A reading near 120 ohms or open points to a broken wire or missing resistor.
Unplug modules one at a time to see whether a faulty one is dragging the network down.
Check for Software Updates
Ask a dealer or a shop with factory software whether an update exists for your vehicle. Many internal PCM codes have been fixed with a software update instead of a new module.
Repairs That Clear the P0600 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Repair network wiring or connectors.
- Replace a faulty module that disturbs the network.
- Remove or rewire aftermarket accessories.
- Fix voltage problems.
- Reprogram or replace the PCM if it has an internal fault.
If the PCM must be replaced, buy one that matches your part number or one programmed for your VIN. Keep the battery on a maintainer during programming, since a voltage drop can ruin the programming.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the PCM before checking power and ground
- Programming a module with a weak battery
- Skipping available software updates
Repair Cost Breakdown
The cost to fix a P0600 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Battery test and terminal cleaning | $0 to $10 | $25 to $75 |
| Ground or power feed repair | $10 to $40 | $100 to $300 |
| PCM software update | $0 | $100 to $250 |
| Remanufactured PCM, programmed | $150 to $500 | $400 to $1,200 |
| New PCM from the dealer | $400 to $1,200 | $800 to $2,000 |
Many network faults are found in the wiring or a connector, which costs far less than a new module.
Can You Drive with a P0600 Code?
It depends on the symptoms. If the engine runs normally, you can usually drive carefully to a repair shop.
If the engine stalls, will not start, runs in limp mode or shifts strangely, avoid driving. A computer fault can shut the engine off without warning.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0601 | Internal Control Module Memory Check Sum Error |
| P0602 | Control Module Programming Error |
| P0603 | Internal Control Module Keep Alive Memory (KAM) Error |
| P0604 | Internal Control Module Random Access Memory (RAM) Error |
| P0605 | Internal Control Module Read Only Memory (ROM) Error |
| P0606 | PCM Processor Fault |
Fixing the PCM Fault
A P0600 code means the PCM found a communication problem. Network wiring faults, failed modules and low voltage cause most cases.
- Test the battery and charging system.
- Check PCM power, ground and connectors.
- Check for software updates.
- Reprogram or replace the PCM only if the tests point to it.
Frequently Asked Questions
What Is a Serial Communication Link?
It is a data connection that lets modules share information, such as engine speed, vehicle speed and warning lights. Most modern vehicles use a CAN network. The PCM may also use an internal link between its own processors.
Can a Weak Battery Cause Computer Codes?
Yes. Low voltage during cranking or a battery that drops out can make the PCM reset, lose memory or fail its self-tests. Test the battery and charging system before you replace any module.
Can I Replace the PCM Myself?
You can swap the hardware, but most new or used PCMs must be programmed for your vehicle, including the VIN and often the immobilizer keys. Without that, the engine may not start. Many owners buy a PCM preprogrammed for their VIN or have a dealer or shop program it.
Will Clearing the Code Fix It?
It may clear for a while, especially if a voltage problem caused it. If the module has a real internal fault, the code will return, often right away. Note the code and freeze frame data before you clear anything.
Are There Software Updates for PCM Codes?
Often, yes. Makers release updates that fix false self-test failures and other known problems. A dealer or a shop with factory software can check whether an update exists for your vehicle.
Can Water Damage the PCM?
Yes. A leaking cowl, a blocked drain or a failed seal can let water reach the PCM or its connectors. Corrosion on the pins or inside the case can cause internal faults. Look for water marks and corrosion when you inspect it.
Where Is the PCM?
It varies by vehicle. Common spots are in the engine bay near the battery or fuse box, on the firewall, behind the glove box or under the cowl. Some trucks mount it on the side of the engine. Your service manual or a parts catalog shows the location.
Can Jump Starting Damage the PCM?
It can if it is done wrong. Connecting the cables backward, or letting them spark across the battery while another vehicle revs hard, can send voltage spikes through the system. Connect positive first, then ground the negative on the engine, and do not rev the donor vehicle.