P0713 Code: Meaning, Symptoms, Causes & Fixes

The transmission computer changes shift timing, pressure and torque converter lockup based on fluid temperature. A P0713 code means the transmission fluid temperature sensor signal voltage is higher than its allowed range, which usually points to an open ground or a short to voltage.

This guide explains how the sensor works, where it is and how to test it from the transmission connector.

P0713 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
7TransmissionThe fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch.
13Specific faultTransmission Fluid Temperature Sensor Circuit High Input

What the P0713 Code Means

The SAE J2012 standard defines the P0713 code as Transmission Fluid Temperature Sensor Circuit High Input. The transmission fluid temperature (TFT) sensor is a thermistor, a resistor that changes value with heat. Its resistance drops as the fluid gets hotter. On most transmissions, it sits inside the case, often on the internal wiring or the solenoid pack, so it is reached by dropping the pan.

The computer sends the sensor a 5-volt reference and reads the voltage that returns. High voltage means cold fluid, and low voltage means hot fluid. Normal fluid temperature is often around 160°F to 200°F, and much higher temperatures shorten fluid life quickly.

The computer uses fluid temperature to delay upshifts when cold, lock the torque converter sooner when hot and protect the transmission from overheating. A false reading can make shifts feel wrong.

High input means the signal voltage rose above the highest value a working transmission fluid temperature sensor should ever send. That usually points to an open ground, a signal wire touching the reference or another voltage source, or a failed sensor.

Symptoms of a Fluid Temperature Sensor Fault

Most symptoms show up in how the transmission shifts. Common signs of a P0713 code include:

  • Check engine light on
  • Harsh or delayed shifts
  • Late upshifts as if the transmission were cold
  • Torque converter not locking up
  • Transmission temperature gauge reading wrong

When the computer cannot trust the reading, it often uses a default temperature. Shifts may feel firm or late, and some transmissions limit torque converter lockup.

What Causes the P0713 Code?

High input faults almost always come from an electrical problem:

  1. Open sensor ground. Without a ground, the signal floats up toward the reference.
  2. Signal wire shorted to the 5-volt reference. Damaged insulation lets the wires touch.
  3. Signal wire shorted to battery voltage. Less common, but possible.
  4. Corroded connector. Resistance on the ground pin raises the signal.
  5. Failed transmission fluid temperature sensor. An internal fault locks the output high.
  6. PCM fault. Rare.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II or transmission scan tool that shows fluid temperature
  • Digital multimeter
  • Wiring diagram and pin chart for your transmission
  • Drain pan and new pan gasket
  • Correct transmission fluid

Step-By-Step Diagnosis of the P0713 Code

Start at the transmission case connector. You can often test the sensor without dropping the pan.

Check Live Data

With the key on, look at fluid temperature in live data. After a cold soak, it should be close to the outside air temperature. A reading stuck at -40°F or an impossible hot value confirms a circuit fault.

Test the Ground First

Back-probe the sensor ground with the key on and measure against the battery negative post. It should read close to 0 volts, ideally under 0.1 volt. A higher reading means a poor ground.

Check for a Short to Voltage

Unplug the transmission fluid temperature sensor with the key on and watch the signal in live data. If it stays high with the sensor unplugged, the signal wire is shorted to the reference or another voltage source. If it changes, the sensor itself is likely at fault.

Measure Resistance at the Case Connector

Unplug the transmission case connector and measure the sensor resistance at the correct pins. Compare it with the temperature chart in your service manual. A cold sensor reads high resistance, and a hot one reads low.

How to Fix the P0713 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Repair the case connector or wiring.
  • Replace the fluid temperature sensor if it fails tests. On some transmissions, it is part of the internal wiring or solenoid pack.
  • Correct the fluid level.
  • Fix real overheating such as a blocked cooler.
  • Replace a leaking case connector seal.

When the sensor is part of the internal wiring or solenoid pack, the whole assembly is replaced. Use a new pan gasket and the correct fluid, and fill it with the procedure in your service manual.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the sensor without testing the ground first
  • Overlooking a short to voltage inside a wiring bundle
  • Ignoring real overheating
  • Replacing the sensor without testing at the case connector

Typical Repair Costs

The cost to fix a P0713 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Connector cleaning or repair$10 to $30$75 to $250
Wiring repair$10 to $40$100 to $300
Fluid temperature sensor$20 to $80$150 to $350
Internal wiring or solenoid pack$100 to $400$300 to $800
Fluid and filter service$40 to $120$150 to $350

The sensor is cheap, but most of the cost is labor to drop the pan and refill the fluid.

Is It Safe to Drive with a P0713 Code?

Usually, yes, for normal driving. The transmission uses a default temperature and keeps working, though shifts may feel different.

Avoid towing and hard driving, since the computer may not protect the transmission from real overheating while the sensor is faulty.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0710Transmission Fluid Temperature Sensor Circuit Malfunction
P0711Transmission Fluid Temperature Sensor Circuit Range/Performance
P0712Transmission Fluid Temperature Sensor Circuit Low Input
P0714Transmission Fluid Temperature Sensor Circuit Intermittent
P0218Transmission Fluid Over Temperature Condition
P0700Transmission Control System Malfunction

Fixing the Fluid Temperature Sensor

A P0713 code means the transmission fluid temperature sensor voltage is too high. Lost grounds, shorts to voltage and failed sensors cause most cases.

  • Confirm the high reading in live data.
  • Test the sensor ground first.
  • Unplug the sensor to check for a short to voltage.
  • Replace the sensor only after the wiring tests good.

Frequently Asked Questions

Can a Bad Ground Cause the P0713 Code?

Yes, and it is one of the most common causes. Without a solid ground, the transmission fluid temperature sensor signal floats up toward the reference voltage. Check the ground pin, the wire and the ground connections at the engine and PCM.

What Is a Normal Transmission Temperature?

Many transmissions run around 160°F to 200°F in normal driving. Temperatures above about 240°F shorten fluid life quickly, and sustained readings near 300°F can damage the transmission.

Why Does My Transmission Shift Late When Cold?

Many computers delay upshifts when the fluid is cold, to warm it faster. If the sensor reads -40°F all the time, the transmission may keep shifting as if it were cold.

Can Low Transmission Fluid Cause Sensor Codes?

Sometimes. Low fluid makes the transmission slip and run hot, which can upset speed and temperature readings and set range codes. Check the fluid level with the procedure in your service manual before you replace a sensor.

Does the Transmission Need a Relearn After a Sensor Repair?

Some do. Many modern transmissions store learned shift data, and a few need a relearn or a reset after a sensor or wiring repair. Check the service manual, especially if shifts feel odd after the fix.

Where Is the Transmission Computer?

On some vehicles, the PCM controls the transmission. On others, a separate transmission control module (TCM) sits under the dash, in the engine bay or bolted inside the transmission. Your service manual shows which one your vehicle uses.

Can I Check the Transmission Fluid Myself?

On many older vehicles, yes, with the dipstick and the engine running in park at operating temperature. Many newer transmissions have no dipstick and are checked at a fill plug with the fluid at a set temperature, often with a scan tool to read it. Follow the procedure for your transmission.

Should I Fix Electrical Codes Before Mechanical Ones?

Yes. A sensor or wiring fault can make the computer shift badly, use limp mode or misjudge gear ratio, which may set other codes that look mechanical. Fix the electrical faults first, clear the codes and see which ones come back.