P0719 Code: Meaning, Symptoms, Causes & Fixes

The brake switch tells the transmission computer when you press the brake, so it can release the torque converter clutch and cancel cruise control. A P0719 code means the computer found a problem in the brake switch B circuit.

This guide explains how the brake switch works with the transmission, what usually goes wrong and how to test it.

P0719 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
7TransmissionThe fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch.
19Specific faultTorque Converter/Brake Switch B Circuit Low

What the P0719 Code Means

The SAE J2012 standard defines the P0719 code as Torque Converter/Brake Switch B Circuit Low. The powertrain control module (PCM) or a separate transmission control module (TCM) runs the automatic transmission. It reads speed sensors, the range sensor, fluid temperature and engine load, then controls shift solenoids, pressure control solenoids and the torque converter clutch.

When it finds a problem, it often turns on the check engine light, stores a detailed transmission code and may switch to limp mode, which holds one gear to protect the transmission.

Many brake switches have two circuits. Brake switch A often runs the brake lights, and brake switch B is a second signal used for torque converter clutch release, cruise cancel and cross-checking switch A. Low means the computer sees low voltage on the switch B circuit when it should be high, or all the time.

Symptoms of a Brake Switch B Fault

Transmission problems are usually easy to feel. Common signs of a P0719 code include:

  • Check engine light on
  • Torque converter not locking up
  • Cruise control not working
  • Engine stalling when you stop on some vehicles
  • Brake lights not working or staying on

If the computer thinks the brake is always pressed, it may never lock the torque converter, and fuel economy drops. If it thinks the brake is never pressed, the converter may stay locked as you stop.

What Causes the P0719 Code?

These are the usual causes:

  1. Misadjusted brake switch. The pedal does not close or open it correctly.
  2. Failed brake switch. The contacts wear out.
  3. Broken pedal stop or bumper. A missing plastic stop lets the switch sit wrong.
  4. Blown fuse. For the switch circuit.
  5. Damaged wiring or connector. Near the pedal.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • Scan tool that can read transmission codes and data
  • Digital multimeter
  • Wiring diagram for your transmission
  • Correct transmission fluid
  • Drain pan and new pan gasket or filter

How to Track Down the P0719 Code

Scan every module for codes first. Many transmission faults store a more specific code that points straight to the cause.

Watch the Switch in Live Data

With the key on, watch brake switch status in live data while you press and release the pedal slowly. Both switch signals should change at about the same point in pedal travel.

Check the Brake Lights

Have a helper check that the brake lights come on when you press the pedal and go off when you release it.

Inspect the Switch and Pedal Stop

Look at the brake switch above the pedal arm. Check that the plastic stop the switch presses against is in place.

Check that the switch is adjusted so it changes with light pedal pressure.

Test the Circuit

Check the fuse. With the switch unplugged, check for power at the feed pin and continuity across the switch B contacts as you press the pedal.

Repairs That Clear the P0719 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Adjust the brake switch.
  • Replace a failed brake switch.
  • Replace a broken pedal stop.
  • Replace a blown fuse after finding the cause.
  • Repair damaged wiring.

Some brake switches self-adjust when you pull the pedal up after installing them. Others use a threaded body and locknut. Follow the service manual, and check the brake lights afterward.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the switch when a pedal stop is broken
  • Ignoring brake lights that stay on
  • Forgetting to check the fuse

Typical Repair Costs

The cost to fix a P0719 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Brake light switch$10 to $50$75 to $200
Pedal stop or bumper$2 to $10$50 to $100
Fuse$1 to $5$25 to $75
Wiring repair$10 to $30$100 to $300

A brake switch is cheap and quick to replace on most vehicles.

Can You Drive with a P0719 Code?

Drive only as far as you need to. Many transmission faults put the vehicle in limp mode, which limits acceleration and top speed and makes merging harder.

If the transmission slips, flares between gears or makes noise, stop driving and have it checked. Driving on a slipping transmission can turn a modest repair into a rebuild.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0700Transmission Control System Malfunction
P0705Transmission Range Sensor Circuit Malfunction (PRNDL Input)
P0715Input/Turbine Speed Sensor Circuit Malfunction
P0720Output Speed Sensor Circuit Malfunction
P0730Incorrect Gear Ratio
P0750Shift Solenoid A Malfunction

Fixing Brake Switch B

A P0719 code means the computer found a problem with the brake switch B circuit. Misadjusted switches, failed switches and broken pedal stops cause most cases.

  • Watch brake switch status in live data.
  • Check the brake lights.
  • Inspect the switch and pedal stop.
  • Test the fuse and circuit.

Frequently Asked Questions

Why Is a Brake Switch Code Stored as a Transmission Code?

The transmission computer uses the brake signal to release the torque converter clutch when you brake. If it cannot trust the signal, it may not lock the converter at all, which is why the code sits with the transmission codes.

Can Low Transmission Fluid Cause Solenoid Codes?

Yes. Low fluid lowers line pressure, so a solenoid may not get the result the computer expects. That can set performance codes even when the solenoid works. Check the fluid level first.

Should I Use a Universal Transmission Fluid?

It is safer to use the exact fluid your transmission specifies, such as a specific ATF or CVT fluid. The wrong fluid can change how clutches engage and how solenoids and valves behave, which can cause harsh shifts or new codes.

Does the Transmission Need a Relearn After Repairs?

Many modern transmissions adapt to wear, and they may need their learned values reset or a relearn drive after solenoid or valve body work. Some need a scan tool procedure. Check the service manual for your transmission.

What Is Limp Mode?

Limp mode is a protection strategy. When the computer finds a serious transmission fault, it holds one gear, often second or third, and may raise line pressure. You can drive slowly to a repair shop, but acceleration and top speed are limited.

Can a Weak Battery Cause Transmission Codes?

Yes. Low or unstable voltage can make the transmission computer reset or misread its sensors and solenoids. Test the battery and charging system if several unrelated codes appear together.

How Much Does a Transmission Scan Cost?

Many shops charge a diagnostic fee, often around $100 to $200, to read the transmission codes and data and test drive the vehicle. Some parts stores read engine codes for free, but their basic readers often cannot see detailed transmission codes.

Should I Clear the Codes Myself?

You can, but write the codes and freeze frame data down first. Clearing them erases the information a technician needs, and the vehicle may relearn shift settings. If the fault is still there, the codes will return.

Will an Extended Warranty Cover This?

It may, depending on the cause and your coverage. Transmission repairs are often covered by powertrain warranties. Check your paperwork before you pay for a repair, and keep records of fluid services, which a warranty company may ask for.