A solenoid that stays on when the computer turns it off can leave the transmission in the wrong gear or state. A P0742 code means the computer saw the torque converter clutch solenoid acting as if it were stuck on.
This guide explains what the torque converter clutch solenoid does, what usually goes wrong and how to test it step by step.
P0742 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 7 | Transmission | The fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch. |
| 42 | Specific fault | Torque Converter Clutch Circuit Stuck On |
What the P0742 Code Means
The SAE J2012 standard defines the P0742 code as Torque Converter Clutch Circuit Stuck On. The torque converter connects the engine to the automatic transmission through fluid. At cruising speed, a clutch inside it locks the engine and transmission together, which cuts slip, heat and fuel use. The torque converter clutch (TCC) solenoid in the valve body controls that lockup.
The powertrain control module (PCM) or transmission control module (TCM) applies the TCC at steady cruise, often above about 40 to 45 mph in higher gears. It compares engine speed with transmission input or turbine speed. When the clutch is locked, the two should be almost the same, with only a few rpm of slip.
Stuck on means the computer sees engine speed and torque converter slip acting as if the torque converter clutch solenoid is on, even when it is commanded off. The solenoid or the valve it controls is usually stuck.
Stuck-On Symptoms of Torque Converter Clutch Solenoid
Transmission faults are usually easy to feel. Common signs of a P0742 code include:
- Engine stalling when you come to a stop
- Engine bogging at low speed in gear
- Check engine light on
- Harsh engagement into drive or reverse
- Shudder when slowing down
A TCC stuck on acts like a manual car with the clutch held in gear. The engine can stall as you stop, because the converter cannot slip.
What Causes the P0742 Code?
These are the usual causes:
- Solenoid stuck open mechanically. Debris holds it open.
- Sticking valve in the valve body. The valve does not return.
- Control wire shorted to ground. On designs where the TCM switches the ground side.
- Dirty or burnt fluid. Varnish makes valves stick.
- Worn torque converter clutch. The clutch lining slips even when applied.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II or transmission scan tool that can command solenoids
- Digital multimeter
- Wiring diagram for your transmission
- Drain pan and new pan gasket or filter
- Correct transmission fluid for your vehicle
Step-By-Step Diagnosis of the P0742 Code
Check for other transmission codes and fix electrical faults first. Then check the fluid, since it causes or worsens many solenoid problems.
Check the Fluid Level and Condition
Check the transmission fluid with the engine at the temperature and in the gear the service manual specifies. Many newer transmissions have no dipstick and use a fill plug and a temperature check. Fluid should be clean and red or amber. Dark, burnt-smelling fluid or metal particles point to internal wear.
Check Live Data
Drive the vehicle and watch the torque converter clutch solenoid command alongside engine speed and torque converter slip in live data. Note whether the result changes when the command changes. Also check for other transmission codes.
Command the Solenoid
With a scan tool, command the torque converter clutch solenoid on and off at the speed and gear the service manual lists. A solenoid that clicks but gives no change points to a mechanical or hydraulic problem.
Inspect the Valve Body and Fluid
Drop the pan and look at the fluid, filter and magnet. Fine clutch material or metal points to internal wear.
Check the solenoid screen and valve for debris. Some solenoids can be cleaned, but a sticking valve body may need repair or replacement.
How to Fix the P0742 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Replace the torque converter clutch solenoid.
- Repair a shorted control wire.
- Repair or replace the valve body if a valve is stuck.
- Change dirty or burnt fluid.
Use the exact fluid your transmission specifies, and fill it with the procedure in the service manual. Many modern transmissions need the fluid checked at a set temperature. After the repair, clear the codes and drive through every gear. Some transmissions need an adaptive relearn.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the solenoid before checking the fluid
- Using the wrong transmission fluid
- Ignoring debris in the pan that points to internal wear
Repair Cost Breakdown
The cost to fix a P0742 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Fluid and filter service | $40 to $120 | $150 to $350 |
| Wiring or connector repair | $10 to $40 | $100 to $300 |
| Single solenoid | $30 to $150 | $200 to $600 |
| Solenoid pack or body | $150 to $500 | $400 to $1,000 |
| Valve body | $300 to $1,000 | $600 to $1,800 |
| Transmission rebuild | $800 to $2,000 in parts | $2,500 to $5,000 |
Wiring and fluid fixes are cheap. A solenoid is moderate, especially if you can reach it by dropping the pan. Valve body and internal repairs cost the most.
Is It Safe to Keep Driving with a P0742 Code?
Usually, for short trips, if the TCC is stuck off. The vehicle drives, but engine speed is higher at cruise, and the transmission runs hotter.
If the TCC is stuck on and the engine stalls at stops, it is not safe to drive, since you can lose power steering and brake assist. Have it towed or repaired before driving far.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0740 | Torque Converter Clutch Circuit Malfunction |
| P0741 | Torque Converter Clutch Circuit Performance or Stuck Off |
| P0743 | Torque Converter Clutch Circuit Electrical |
| P0744 | Torque Converter Clutch Circuit Intermittent |
| P0700 | Transmission Control System Malfunction |
| P0218 | Transmission Fluid Over Temperature Condition |
Fixing the Torque Converter Clutch Solenoid
A P0742 code means the torque converter clutch solenoid seems stuck on. Stuck solenoids, sticking valves and shorted control wires cause most cases.
- Check the fluid level and condition.
- Watch the solenoid command and result in live data.
- Check the control wire for a short to ground.
- Inspect the solenoid and valve body.
Frequently Asked Questions
Why Does My Engine Stall When I Stop?
If the torque converter clutch stays applied, the engine and transmission stay locked together, much like a manual car with the clutch released. When the wheels stop, the engine stalls. Replacing a stuck solenoid or fixing a sticking valve usually cures it.
What Is Torque Converter Shudder?
Shudder feels like driving over rumble strips, often around 40 to 50 mph under light throttle. It usually comes from the torque converter clutch slipping as it applies. A fluid change with the correct fluid sometimes helps, but a worn converter may need replacing.
Can the P0742 Code Damage My Transmission?
Over time, yes. A slipping converter, or one that never locks, makes extra heat, and heat is the main enemy of transmission fluid and clutches. Fix it soon to protect the transmission.
Can Low Transmission Fluid Cause Solenoid Codes?
Yes. Low fluid lowers line pressure, so a solenoid may not get the result the computer expects. That can set performance codes even when the solenoid works. Check the fluid level first.
Will a Fluid Change Fix Solenoid Codes?
Sometimes. Fresh fluid can help a sticking solenoid or valve, especially if the old fluid was dirty. It will not fix an electrical fault or a badly worn part. Use the exact fluid your transmission requires.
Do I Need to Remove the Transmission to Replace a Solenoid?
Usually not. On many transmissions, the solenoids are on the valve body, which you reach by removing the transmission pan. On some, they are part of a solenoid pack or a transmission control module bolted to the valve body. A few designs need more disassembly.
Should I Use a Universal Transmission Fluid?
It is safer to use the exact fluid your transmission specifies, such as a specific ATF or CVT fluid. The wrong fluid can change how clutches engage and how solenoids and valves behave, which can cause harsh shifts or new codes.