P0744 Code: Meaning, Symptoms, Causes & Fixes

A solenoid circuit that drops out for a moment can make shifts erratic and come back to normal on the next drive. A P0744 code means the computer caught the torque converter clutch solenoid circuit cutting in and out.

This guide explains what the torque converter clutch solenoid does, what usually goes wrong and how to test it step by step.

P0744 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
7TransmissionThe fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch.
44Specific faultTorque Converter Clutch Circuit Intermittent

What the P0744 Code Means

The SAE J2012 standard defines the P0744 code as Torque Converter Clutch Circuit Intermittent. The torque converter connects the engine to the automatic transmission through fluid. At cruising speed, a clutch inside it locks the engine and transmission together, which cuts slip, heat and fuel use. The torque converter clutch (TCC) solenoid in the valve body controls that lockup.

The powertrain control module (PCM) or transmission control module (TCM) applies the TCC at steady cruise, often above about 40 to 45 mph in higher gears. It compares engine speed with transmission input or turbine speed. When the clutch is locked, the two should be almost the same, with only a few rpm of slip.

Intermittent means the torque converter clutch solenoid circuit dropped out or misbehaved for short moments. The fault may last only a fraction of a second, so it often tests fine when parked.

Signs of an Intermittent Fault in Torque Converter Clutch Solenoid

Transmission faults are usually easy to feel. Common signs of a P0744 code include:

  • Check engine light on
  • Higher engine rpm at highway speed
  • Lower fuel economy
  • Transmission running hot
  • Shudder at about 40 to 50 mph

If the TCC never locks, engine speed stays a few hundred rpm higher at cruise than normal, and fuel economy drops. Slipping also makes extra heat, which wears the fluid faster.

Common Causes of the P0744 Code

These are the usual causes:

  1. Loose case connector. Vibration loosens it.
  2. Corroded or spread terminals. Weak pins lose contact.
  3. Chafed wiring. Near the transmission or exhaust.
  4. Fluid in the connector. A leaking seal at the case.
  5. Failing torque converter clutch solenoid. An internal fault comes and goes with heat.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II or transmission scan tool that can command solenoids
  • Digital multimeter
  • Wiring diagram for your transmission
  • Drain pan and new pan gasket or filter
  • Correct transmission fluid for your vehicle

How to Diagnose the P0744 Code

Check for other transmission codes and fix electrical faults first. Then check the fluid, since it causes or worsens many solenoid problems.

Check the Fluid Level and Condition

Check the transmission fluid with the engine at the temperature and in the gear the service manual specifies. Many newer transmissions have no dipstick and use a fill plug and a temperature check. Fluid should be clean and red or amber. Dark, burnt-smelling fluid or metal particles point to internal wear.

Wiggle Test the Circuit

With the engine running and the solenoid commanded on, gently wiggle the case connector and wiring while you watch live data or the solenoid status. A sudden change or a new code marks the bad spot.

Inspect the Case Connector

Unplug the case connector and look for transmission fluid, corrosion and spread pins. A leaking connector seal is a common cause and lets fluid wick up the wiring.

Check Resistance Hot and Cold

Measure the torque converter clutch solenoid resistance at the case connector with the transmission cold, then after a drive. Many TCC solenoids read roughly 10 to 25 ohms, but check the specification for your transmission. A reading that jumps or goes open when hot points to a failing coil.

Repairs That Clear the P0744 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Repair loose or corroded terminals.
  • Replace a leaking case connector seal.
  • Repair chafed wiring.
  • Replace a failing torque converter clutch solenoid.

Use the exact fluid your transmission specifies, and fill it with the procedure in the service manual. Many modern transmissions need the fluid checked at a set temperature. After the repair, clear the codes and drive through every gear. Some transmissions need an adaptive relearn.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the solenoid before checking the fluid
  • Using the wrong transmission fluid
  • Ignoring debris in the pan that points to internal wear

Typical Repair Costs

The cost to fix a P0744 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Fluid and filter service$40 to $120$150 to $350
Wiring or connector repair$10 to $40$100 to $300
Single solenoid$30 to $150$200 to $600
Solenoid pack or body$150 to $500$400 to $1,000
Valve body$300 to $1,000$600 to $1,800
Transmission rebuild$800 to $2,000 in parts$2,500 to $5,000

Wiring and fluid fixes are cheap. A solenoid is moderate, especially if you can reach it by dropping the pan. Valve body and internal repairs cost the most.

Can You Drive with a P0744 Code?

Usually, for short trips, if the TCC is stuck off. The vehicle drives, but engine speed is higher at cruise, and the transmission runs hotter.

If the TCC is stuck on and the engine stalls at stops, it is not safe to drive, since you can lose power steering and brake assist. Have it towed or repaired before driving far.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0740Torque Converter Clutch Circuit Malfunction
P0741Torque Converter Clutch Circuit Performance or Stuck Off
P0742Torque Converter Clutch Circuit Stuck On
P0743Torque Converter Clutch Circuit Electrical
P0700Transmission Control System Malfunction
P0218Transmission Fluid Over Temperature Condition

Fixing the Torque Converter Clutch Solenoid

A P0744 code means the torque converter clutch solenoid circuit cuts in and out. Loose connectors, leaking case seals and chafed wiring cause most cases.

  • Check the fluid level and condition.
  • Wiggle test the wiring.
  • Inspect the case connector for fluid.
  • Check resistance hot and cold.

Frequently Asked Questions

Why Does the P0744 Code Come and Go?

Heat and vibration can make a weak connection or a failing coil open for a moment. The fault often appears only after the transmission warms up. Checking resistance hot and cold helps catch it.

What Is Torque Converter Shudder?

Shudder feels like driving over rumble strips, often around 40 to 50 mph under light throttle. It usually comes from the torque converter clutch slipping as it applies. A fluid change with the correct fluid sometimes helps, but a worn converter may need replacing.

Can the P0744 Code Damage My Transmission?

Over time, yes. A slipping converter, or one that never locks, makes extra heat, and heat is the main enemy of transmission fluid and clutches. Fix it soon to protect the transmission.

Can Low Transmission Fluid Cause Solenoid Codes?

Yes. Low fluid lowers line pressure, so a solenoid may not get the result the computer expects. That can set performance codes even when the solenoid works. Check the fluid level first.

Will a Fluid Change Fix Solenoid Codes?

Sometimes. Fresh fluid can help a sticking solenoid or valve, especially if the old fluid was dirty. It will not fix an electrical fault or a badly worn part. Use the exact fluid your transmission requires.

Do I Need to Remove the Transmission to Replace a Solenoid?

Usually not. On many transmissions, the solenoids are on the valve body, which you reach by removing the transmission pan. On some, they are part of a solenoid pack or a transmission control module bolted to the valve body. A few designs need more disassembly.

Should I Use a Universal Transmission Fluid?

It is safer to use the exact fluid your transmission specifies, such as a specific ATF or CVT fluid. The wrong fluid can change how clutches engage and how solenoids and valves behave, which can cause harsh shifts or new codes.