The P1104 code is a manufacturer-specific code, so its meaning depends on who built your vehicle. On Ford it points to the mass airflow sensor, on Chrysler it points to the turbo boost control and on VW/Audi it points to the oxygen sensor. Each of those is a different part with a different test.
This guide explains the meaning for each make, the symptoms and causes you can expect on each one, and how to track down the real fault before you spend money on parts.
P1104 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. The second character tells you whether the definition is shared by every maker or set by the carmaker itself. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine, transmission or driveline systems. |
| 1 | Manufacturer-specific code | The carmaker sets the definition, so the same code can mean different things on different brands. |
| 1 | Fuel and air metering | The fault involves fuel and air metering, such as airflow, temperature, throttle and oxygen sensors or fuel control. |
| 04 | Specific fault | Set by each maker. See the table below for the makes that use it. |
What the P1104 Code Means by Make
Find your make in the table first, then read its section below. The definitions come from published factory code lists for each maker. Some makers changed a code’s meaning between model years, so confirm it with a scan tool set to your exact vehicle.
| Make | Definition | System Involved |
|---|---|---|
| Ford, Lincoln and Mercury | MAF Sensor Ground Circuit Malfunction | Mass airflow sensor |
| Chrysler, Dodge, Jeep and Ram | Turbocharger Wastegate Solenoid malfunction | Turbo boost control |
| Volkswagen, Audi, Seat and Skoda | Bank 1 sensor 2 O2 signal reads too low, likely from an air leak (VAG fault 17512) | Oxygen sensor |
| Subaru | Engine Torque Control Signal Circuit Malfunction | Traction control and torque request |
| Mitsubishi | Turbocharger Wastegate Solenoid | Turbo boost control |
| Other makes | No confirmed definition | Check with a scan tool set to your make |
Ford, Lincoln and Mercury: Mass Airflow Sensor
On Ford, Lincoln and Mercury vehicles, this code is listed as MAF Sensor Ground Circuit Malfunction. The mass airflow (MAF) sensor sits in the intake tube between the air filter and the throttle body. It measures how much air the engine is taking in, and the engine computer uses that reading as the main input for fuel delivery and engine load.
How the Mass Airflow Sensor Fault Sets
The computer found a problem in the mass airflow sensor circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.
Mass Airflow Sensor Symptoms
- Check engine light on.
- Hesitation or stumbling on acceleration.
- Rough idle or stalling.
- Poor fuel economy.
Mass Airflow Sensor Causes
- Damaged connector or wire.
- Failed mass airflow sensor.
- Shorted 5-volt reference or poor sensor ground.
- Dirty or oil-coated sensing element.
- Air leak between the sensor and the throttle body.
How to Test the Mass Airflow Sensor
Check the connector for corrosion and the wires for rubbing or heat damage. Measure the part’s resistance or output with a meter or scope, then check each wire for continuity from the part to the computer connector.
Check the intake tube for cracks and loose clamps after the sensor. Compare the reading in live data with the expected value for your engine, which is often about 2 to 7 grams per second at warm idle on small engines. Clean the element with MAF sensor cleaner only, then retest. Snap the throttle and watch for a smooth rise in the reading.
Mass Airflow Sensor Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the mass airflow sensor only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Mass Airflow Sensor Mistakes to Avoid
- Cleaning the MAF sensor with carburetor or brake cleaner, which can damage it.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Chrysler and Mitsubishi: Boost Control
These makers all use this number for a fault in the turbo boost control, but each words it differently:
- Chrysler, Dodge, Jeep and Ram: Turbocharger Wastegate Solenoid malfunction.
- Mitsubishi: Turbocharger Wastegate Solenoid.
On turbocharged engines, the engine computer controls boost with a wastegate or bypass solenoid and checks the result with a boost pressure sensor. It sets a code when actual boost does not match the target or the control circuit fails.
How the Boost Control Fault Sets
The computer found a problem in the turbo boost control circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.
Boost Control Symptoms
- Check engine light on.
- Loss of power or limp mode.
- Hissing or whistling from a boost leak.
- Overboost surge in some cases.
Boost Control Causes
- Damaged connector or wire.
- Failed part in the turbo boost control.
- Blown fuse or failed relay in the feed circuit.
- Cracked boost hose or loose intercooler clamp.
- Failed boost control solenoid.
How to Test the Boost Control
Unplug the part and measure its resistance against the specification. With the key on, check for battery voltage on the feed wire. Then check the control wire for continuity back to the computer and for any short to ground or to voltage. A scan tool that can command the part on and off makes this faster.
Pressure test the intake side for leaks between the turbo and the engine. Check the vacuum lines to the wastegate or bypass valve. Command the boost control solenoid with a scan tool, and compare desired and actual boost in live data during a road test.
Boost Control Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the failed part in the turbo boost control only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Boost Control Mistakes to Avoid
- Replacing the part without checking its fuse, power feed and control wire.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Volkswagen, Audi, Seat and Skoda: Oxygen Sensor
On Volkswagen, Audi, Seat and Skoda vehicles, this code is listed as Bank 1 sensor 2 O2 signal reads too low, likely from an air leak (VAG fault 17512). Oxygen sensors in the exhaust tell the engine computer whether the mixture is rich or lean. The front sensor is used for fuel control and switches quickly once the engine is warm. The rear sensor watches the catalytic converter. Some newer engines use a wide-band air-fuel sensor that reads the exact mixture.
What Sets the Oxygen Sensor Fault
Range or performance means the oxygen sensor circuit works electrically, but the reading or result does not make sense for the conditions, or does not agree with related sensors. The part may be worn, sticking or reporting a real problem elsewhere.
Oxygen Sensor Symptoms
- Check engine light on.
- Higher fuel use.
- Rough idle or hesitation in some cases.
- Failed emissions test.
Oxygen Sensor Causes
- Worn or contaminated oxygen sensor.
- Exhaust leak ahead of the sensor that lets in outside air.
- Vacuum leak or fuel pressure problem that really is making the mixture lean or rich.
- Misfire that sends unburned oxygen past the sensor.
- Sensor wires swapped after a repair.
- Damaged connector or wiring.
How to Test the Oxygen Sensor
Warm the engine fully and watch the sensor in live data. A front sensor should switch between about 0.1 and 0.9 volts several times a second at 2,000 rpm. A lazy or stuck reading points to the sensor. A reading that stays lean along with high positive fuel trim points to a real lean condition, so look for vacuum and exhaust leaks before you replace the sensor.
If the readings point to a part, check its connector and wiring before you replace it, since a poor connection can cause the same result.
Oxygen Sensor Repairs
- Fix the cause the tests point to, starting with the simplest one: worn or contaminated oxygen sensor.
- Replace the oxygen sensor only if testing confirms it is at fault.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Oxygen Sensor Mistakes to Avoid
- Replacing the oxygen sensor before checking for vacuum and exhaust leaks.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Subaru: Traction Control and Torque Request
On Subaru vehicles, this code is listed as Engine Torque Control Signal Circuit Malfunction. The ABS or traction control module asks the engine computer to cut torque when a wheel spins. The engine computer answers with a torque signal. These requests travel over a dedicated wire or the data network, and a code sets when the signal is missing or out of range.
When the Computer Flags the Traction Control and Torque Request
The computer found a problem in the traction control and torque request circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.
Traction Control and Torque Request Symptoms
- Traction control or ABS light on.
- Check engine light on.
- Traction control not working or cutting power when it should not.
Traction Control and Torque Request Causes
- Damaged connector or wire.
- Failed part in the traction control and torque request.
- Blown fuse or failed relay in the feed circuit.
- Fault stored in the ABS or traction control module.
- Failed wheel speed sensor.
How to Test the Traction Control and Torque Request
Check battery voltage, fuses and grounds first. Then check the power, ground and signal wires at the part or module named in the code, and scan the other modules for related codes.
Read codes in the ABS and traction control modules first, since this code is often a result of a fault there. Check the wheel speed sensors in live data on a test drive, then check the torque signal wiring between the modules.
Traction Control and Torque Request Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the failed part in the traction control and torque request only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Traction Control and Torque Request Mistakes to Avoid
- Working on the engine computer before reading the codes in the ABS module.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Other Makes
We could not confirm a definition for Toyota, Honda, Nissan, GM, Hyundai, Kia, Mazda, BMW or Mercedes-Benz. If your scanner shows the P1104 code on one of those makes, read it again with a scan tool set to the exact make, model and year, or check the factory service information. A generic code reader may show the Ford meaning for every vehicle, which can send you after the wrong part.
How to Confirm Which Meaning Applies to Your Vehicle
A code number alone is not enough on manufacturer-specific codes. Use these steps to make sure you are chasing the right fault.
- Pick the correct make and model in your scan tool, so it uses that maker’s code library.
- Write down the full description the tool shows, plus any other codes stored with it.
- Use the freeze frame data to see when the fault set, such as cold start, idle or highway speed.
- Match the code with the service information for your exact engine and model year.
- If two sources disagree, trust the one tied to your VIN, such as a dealer or a factory repair manual.
Tools You Will Need
- OBD-II scan tool with live data and a make-specific code library.
- Digital multimeter.
- Lab scope or graphing meter (helpful for signal checks).
- MAF sensor cleaner.
- Test light or noid light.
- Boost leak tester.
- Oxygen sensor socket.
Repair Cost Breakdown
Costs depend on which maker’s meaning applies to your vehicle. These are typical ranges for parts and shop labor.
| Repair | Make | Typical Cost |
|---|---|---|
| Clean and reseat the connector | All | $0 to $60 |
| Clean or replace the mass airflow sensor | Ford | $10 to $350 |
| Repair a boost leak or replace the boost control solenoid | Chrysler, Mitsubishi | $50 to $800 |
| Replace the oxygen sensor | VW/Audi | $100 to $400 |
| Fix the ABS or traction control fault | Subaru | $100 to $500 |
| Repair a damaged wire | All | $80 to $250 |
Is It Safe to Drive with a P1104 Code?
It depends on which meaning applies to your vehicle. On Ford and VW/Audi vehicles, short trips are usually fine, but fuel use, emissions or comfort may suffer until you fix it. On Chrysler vehicles, drive gently and get it checked soon, because the engine can lose power or overboost. On Subaru vehicles, drive gently and get it checked soon, because traction control may not work on slippery roads. On Mitsubishi vehicles, drive gently and get it checked soon, because the engine can lose power or overboost. Stop driving if the check engine light starts flashing, the engine overheats or the vehicle loses power on the road.
When to See a Shop
Some of the checks in this guide need more than a meter. Module programming, transmission tests and key or immobilizer work usually need a dealer-level scan tool. If the basic checks for Subaru come back clean, a shop with factory software for your make can run the guided tests and confirm the fault before parts are replaced.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P1103 | MAF in Range but Higher Than Expected |
| P1102 | MAF in Range but Lower Than Expected |
| P1101 | MAF Sensor Out of Self-Test Range |
| P1100 | MAF Sensor Intermittent |
| P0171 | System Too Lean (Bank 1) |
| P0103 | Mass or Volume Air Flow Circuit High Input |
Fixing the P1104 Code
The fix for a P1104 code depends on the make, so confirm the meaning first.
- Ford: check the intake tube for cracks and loose clamps after the sensor.
- Chrysler: pressure test the intake side for leaks between the turbo and the engine.
- VW/Audi: warm the engine fully and watch the sensor in live data.
- Subaru: read codes in the ABS and traction control modules first, since this code is often a result of a fault there.
- Mitsubishi: pressure test the intake side for leaks between the turbo and the engine.
- Any make: repair wiring and connectors before you replace a part.
Frequently Asked Questions
Why Does My Scanner Show a Different Meaning for This Code?
Basic code readers often show one maker’s definition for every manufacturer-specific code. Because P1 codes belong to each carmaker, the P1104 code on one brand is not the same fault as on another. A scan tool set to your exact make gives the right meaning.
Can I Clean the Mass Airflow Sensor Instead of Replacing It?
Often, yes. Use spray cleaner made for MAF sensors, never touch the sensing wires, and let it dry fully before you reinstall it. If the readings are still wrong after cleaning, replace the sensor.
How Do I Find a Boost Leak?
Pressurize the intake through the turbo inlet with a boost leak tester, then listen and spray soapy water on the hoses and clamps. Oil residue on a hose joint often marks the leak.
Should I Replace the Oxygen Sensor Right Away?
Not until you rule out vacuum leaks, exhaust leaks and fuel pressure problems. Oxygen sensors often report a real mixture problem correctly, and a new sensor will set the same code if the real cause is still there.
Can I Just Clear the P1104 Code?
You can, but it returns if the fault is still there. Clearing the P1104 code also resets the readiness monitors, so the vehicle needs a few days of normal driving before it can pass an emissions test.