P1109 Code: Meaning, Symptoms, Causes & Fixes

The P1109 code is a manufacturer-specific code, so its meaning depends on who built your vehicle. On Ford it points to the intake air temperature sensor, on GM it points to the throttle and pedal position system and on VW/Audi it points to the oxygen sensor. Each of those is a different part with a different test.

This guide explains the meaning for each make, the symptoms and causes you can expect on each one, and how to track down the real fault before you spend money on parts.

P1109 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. The second character tells you whether the definition is shared by every maker or set by the carmaker itself. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine, transmission or driveline systems.
1Manufacturer-specific codeThe carmaker sets the definition, so the same code can mean different things on different brands.
1Fuel and air meteringThe fault involves fuel and air metering, such as airflow, temperature, throttle and oxygen sensors or fuel control.
09Specific faultSet by each maker. See the table below for the makes that use it.

What the P1109 Code Means by Make

Find your make in the table first, then read its section below. The definitions come from published factory code lists for each maker. Some makers changed a code’s meaning between model years, so confirm it with a scan tool set to your exact vehicle.

MakeDefinitionSystem Involved
Ford, Lincoln and MercuryIAT B Sensor IntermittentIntake air temperature sensor
GM (Chevrolet, GMC, Buick, Cadillac, Pontiac, Oldsmobile, Saturn)Secondary port throttle systemThrottle and pedal position system
Volkswagen, Audi, Seat and SkodaBank 2 sensor 2 O2 signal reads too low, likely from an air leak (VAG fault 17517)Oxygen sensor
Other makesNo confirmed definitionCheck with a scan tool set to your make

Ford, Lincoln and Mercury: Intake Air Temperature Sensor

On Ford, Lincoln and Mercury vehicles, this code is listed as IAT B Sensor Intermittent. The intake air temperature sensor reads the temperature of the air entering the engine. It sits in the air cleaner, the intake tube, the mass airflow sensor or the intake manifold. The computer uses it to fine-tune fuel and spark timing. It is a thermistor, so its resistance drops as it gets hotter. The engine computer feeds it a 5-volt reference through a resistor and reads the voltage, which is high when cold and low when hot.

How the Intake Air Temperature Sensor Fault Sets

The computer saw the intake air temperature sensor signal drop out or jump for a short time and then come back. Intermittent codes almost always point to a loose connector pin, a chafed wire or a part that fails only when hot or cold.

Intake Air Temperature Sensor Symptoms

  • Check engine light on.
  • Slight hesitation or rough running.
  • Small drop in fuel economy.
  • Often no change in how the engine runs.

Intake Air Temperature Sensor Causes

  • Loose connector pin or corrosion.
  • Wire chafed against a bracket or hot part.
  • Part that fails only when hot or cold.
  • Failed intake air temperature sensor.
  • Sensor built into a mass airflow sensor that has failed.

How to Test the Intake Air Temperature Sensor

Unplug the sensor and look for corrosion or bent pins. With the key on, measure about 5 volts on the signal wire at the connector. Check the ground wire for less than about 0.1 volt drop to the battery negative. Measure the sensor resistance and compare it with a temperature chart.

Check that the connector is plugged in, since this sensor is often disturbed during air filter changes. Compare the reading in live data with the real temperature. After the vehicle has sat overnight, it should read close to the outside air temperature. Unplug the sensor: the reading should drop to about -40 degrees. Jumper the two connector pins: it should jump very hot. If both work, the wiring and computer are fine and the sensor is at fault. Measure the sensor resistance against the chart in the service information.

Intake Air Temperature Sensor Repairs

  1. Clean, reseat or replace the connector if the pins are loose, bent or corroded.
  2. Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
  3. Replace the intake air temperature sensor only if it fails the resistance, voltage or live data test.
  4. Clear the code and drive through the same conditions that set it to confirm the repair.

Intake Air Temperature Sensor Mistakes to Avoid

  • Replacing the sensor because the code names it, without checking the connector and wiring first.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

GM Vehicles: Throttle Position System

On GM vehicles, this code is listed as Secondary port throttle system. The throttle position sensor tells the engine computer how far the throttle is open. On drive-by-wire engines, the accelerator pedal has its own position sensors, and an electric motor in the throttle body opens the throttle. The computer compares all of these signals and limits power if they do not agree.

When the Computer Flags the Throttle Position System

The computer watches the throttle and pedal position system on every drive and stores the code when it sees the condition in the definition. The code describes a result, not a failed part, so the cause has to be found with tests.

Throttle Position System Symptoms

  • Check engine light on, sometimes with a reduced power or wrench light.
  • Hesitation or flat spots on acceleration.
  • High or unstable idle.
  • Limp mode with very limited throttle opening.

Throttle Position System Causes

  • Carbon buildup that keeps the throttle plate from closing.
  • Worn spot on the sensor track.
  • Throttle body motor or gear failure.
  • Throttle relearn not done after cleaning or a battery change.
  • Damaged connector or wiring.

How to Test the Throttle Position System

Watch the sensor percentage in live data while you move the throttle or pedal slowly. It should rise smoothly with no drops or jumps. On drive-by-wire systems, the two sensor signals should track each other. Clean carbon from the throttle bore with the key off, then run the throttle relearn procedure for your vehicle.

If the readings point to a part, check its connector and wiring before you replace it, since a poor connection can cause the same result.

Throttle Position System Repairs

  1. Fix the cause the tests point to, starting with the simplest one: carbon buildup that keeps the throttle plate from closing.
  2. Clean or replace the throttle body or pedal sensor only if testing confirms it is at fault.
  3. Clear the code and drive through the same conditions that set it to confirm the repair.

Throttle Position System Mistakes to Avoid

  • Skipping the relearn after cleaning or replacing a throttle body or pedal sensor.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

Volkswagen, Audi, Seat and Skoda: Oxygen Sensor

On Volkswagen, Audi, Seat and Skoda vehicles, this code is listed as Bank 2 sensor 2 O2 signal reads too low, likely from an air leak (VAG fault 17517). Oxygen sensors in the exhaust tell the engine computer whether the mixture is rich or lean. The front sensor is used for fuel control and switches quickly once the engine is warm. The rear sensor watches the catalytic converter. Some newer engines use a wide-band air-fuel sensor that reads the exact mixture.

How the Oxygen Sensor Fault Sets

Range or performance means the oxygen sensor circuit works electrically, but the reading or result does not make sense for the conditions, or does not agree with related sensors. The part may be worn, sticking or reporting a real problem elsewhere.

Oxygen Sensor Symptoms

  • Check engine light on.
  • Higher fuel use.
  • Rough idle or hesitation in some cases.
  • Failed emissions test.

Oxygen Sensor Causes

  • Worn or contaminated oxygen sensor.
  • Exhaust leak ahead of the sensor that lets in outside air.
  • Vacuum leak or fuel pressure problem that really is making the mixture lean or rich.
  • Misfire that sends unburned oxygen past the sensor.
  • Sensor wires swapped after a repair.
  • Damaged connector or wiring.

How to Test the Oxygen Sensor

Warm the engine fully and watch the sensor in live data. A front sensor should switch between about 0.1 and 0.9 volts several times a second at 2,000 rpm. A lazy or stuck reading points to the sensor. A reading that stays lean along with high positive fuel trim points to a real lean condition, so look for vacuum and exhaust leaks before you replace the sensor.

If the readings point to a part, check its connector and wiring before you replace it, since a poor connection can cause the same result.

Oxygen Sensor Repairs

  1. Fix the cause the tests point to, starting with the simplest one: worn or contaminated oxygen sensor.
  2. Replace the oxygen sensor only if testing confirms it is at fault.
  3. Clear the code and drive through the same conditions that set it to confirm the repair.

Oxygen Sensor Mistakes to Avoid

  • Replacing the oxygen sensor before checking for vacuum and exhaust leaks.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

Other Makes

We could not confirm a definition for Toyota, Honda, Nissan, Chrysler, Hyundai, Kia, Mazda, Subaru, BMW or Mercedes-Benz. If your scanner shows the P1109 code on one of those makes, read it again with a scan tool set to the exact make, model and year, or check the factory service information. A generic code reader may show the Ford meaning for every vehicle, which can send you after the wrong part.

How to Confirm Which Meaning Applies to Your Vehicle

Because the same number means different things on different makes, confirm the meaning before you buy parts.

  • Set your scan tool to the exact make, model, year and engine before you read codes.
  • Read the full code description on the tool, not just the number.
  • Check freeze frame data to see the engine speed, temperature and load when the code set.
  • Look up the code in the factory service information or a repair database for your exact vehicle.
  • Ask a dealer parts or service desk to confirm the meaning for your VIN if you are still unsure.

Tools You Will Need

  • OBD-II scan tool with live data and a make-specific code library.
  • Digital multimeter.
  • Infrared thermometer.
  • Back-probe pins.
  • Throttle body cleaner.
  • Lab scope or graphing meter (helpful for signal checks).
  • Oxygen sensor socket.

Repair Cost Breakdown

Costs depend on which maker’s meaning applies to your vehicle. These are typical ranges for parts and shop labor.

RepairMakeTypical Cost
Clean and reseat the connectorAll$0 to $60
Replace the intake air temperature sensorFord$30 to $150
Clean or replace the throttle body or pedal sensorGM$50 to $700
Replace the oxygen sensorVW/Audi$100 to $400
Repair a damaged wireAll$80 to $250

Is It Safe to Drive with a P1109 Code?

It depends on which meaning applies to your vehicle. On Ford and VW/Audi vehicles, short trips are usually fine, but fuel use, emissions or comfort may suffer until you fix it. On GM vehicles, drive gently and get it checked soon, because the throttle can drop into reduced power mode. Stop driving if the check engine light starts flashing, the engine overheats or the vehicle loses power on the road.

When to See a Shop

Most of the checks in this guide need only a scan tool with live data, a multimeter and some patience. See a shop if the wiring is buried somewhere hard to reach, if the code keeps coming back after the obvious fixes, or if the engine runs badly enough that driving to the shop is a risk. Bring the full code description, the freeze frame data and a list of what you have already tested, so the shop does not repeat the same steps.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P1110IAT Sensor (D/C) Open or Short Circuit
P1112IAT Sensor Intermittent
P1113IAT Sensor (L/C) Open or Short Circuit
P1114IAT B Circuit Low Input
P1115IAT B Circuit High Input
P1404IAT B Circuit Malfunction

Fixing the P1109 Code

The fix for a P1109 code depends on the make, so confirm the meaning first.

  • Ford: check that the connector is plugged in, since this sensor is often disturbed during air filter changes.
  • GM: watch the sensor percentage in live data while you move the throttle or pedal slowly.
  • VW/Audi: warm the engine fully and watch the sensor in live data.
  • Any make: repair wiring and connectors before you replace a part.

Frequently Asked Questions

Why Does My Scanner Show a Different Meaning for This Code?

Basic code readers often show one maker’s definition for every manufacturer-specific code. Because P1 codes belong to each carmaker, the P1109 code on one brand is not the same fault as on another. A scan tool set to your exact make gives the right meaning.

How Do I Test a Temperature Sensor?

Measure its resistance at a known temperature and compare it with the chart in the service information. Then unplug it and jumper the connector to check that the computer reads the circuit.

Do I Need to Relearn the Throttle After Cleaning It?

On most drive-by-wire engines, yes. The computer learns the closed throttle position, and a clean throttle body can cause a high idle until the relearn runs. Some vehicles relearn on their own after a key cycle, while others need a scan tool.

Should I Replace the Oxygen Sensor Right Away?

Not until you rule out vacuum leaks, exhaust leaks and fuel pressure problems. Oxygen sensors often report a real mixture problem correctly, and a new sensor will set the same code if the real cause is still there.

Will the P1109 Code Come Back After Clearing It?

If the fault is still there, yes. The computer retests the system on every drive. After a real fix, the light stays off and the stored P1109 code erases itself after a number of clean drive cycles. Clearing it with a scan tool also resets the readiness monitors, so drive for a few days before an emissions test.