P0568 Code: Meaning, Symptoms, Causes & Fixes

When one cruise button stops working, the problem is often in the switch or the wiring behind the steering wheel. A P0568 code means the engine computer found a problem with the cruise control set signal.

This guide explains how the set signal reaches the engine computer, what usually fails and how to test it.

P0568 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
5Vehicle speed, idle control and auxiliary inputsThe fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control.
68Specific faultCruise Control Set Signal Malfunction

What the P0568 Code Means

The SAE J2012 standard defines the P0568 code as Cruise Control Set Signal Malfunction. On most vehicles, the powertrain control module (PCM) runs the cruise control. It reads the cruise switches on the steering wheel or stalk, the brake switch and vehicle speed, then holds speed by moving the electronic throttle. Older vehicles use a cable and a separate servo.

Many vehicles send all the cruise buttons to the PCM on one or two wires through a resistor ladder. Each button gives a different voltage, so the PCM can tell which one is pressed. On steering wheel switches, the signal passes through the clockspring, a coiled ribbon cable behind the steering wheel.

The set signal tells the PCM to hold the speed you are driving at. On many vehicles, the same button also lowers the set speed when you hold it. The PCM sets this code when it sees that signal stuck on, out of range or not matching the other switch inputs.

Symptoms of a Cruise Set Signal Fault

Most cruise faults only affect the cruise control. Common signs of a P0568 code include:

  • Cruise control not working
  • One cruise button not responding
  • Cruise canceling by itself
  • Cruise light behaving oddly
  • Check engine light on some vehicles

Other steering wheel buttons, the horn or the airbag light acting up at the same time points to the clockspring.

What Causes the P0568 Code?

These are the usual causes:

  1. Worn cruise switch. The contacts wear or get sticky from spills.
  2. Failed clockspring. The ribbon cable behind the wheel breaks.
  3. Corroded connector. Moisture gets into the switch or connector.
  4. Damaged wiring. In the steering column or at the PCM.
  5. Stuck button. A button that does not spring back holds the signal on.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II scan tool that shows cruise switch status
  • Digital multimeter
  • Wiring diagram for your vehicle
  • Trim tools for removing steering wheel covers
  • Contact cleaner

How to Diagnose the P0568 Code

Watch the switch status in live data while you press each button. It is the quickest way to see what the PCM sees.

Watch the Switch in Live Data

With the key on, watch the cruise switch status or voltage in live data. Press the set button and the others one at a time. Each should change the reading cleanly. A button that does nothing, or a reading that stays on, points to the switch or wiring.

Check the Button Itself

Make sure the set button moves freely and springs back. Spilled drinks and dirt can make buttons stick. Gently clean around the button with contact cleaner.

Test the Switch Resistance

Following the service manual, remove the switch and measure its resistance as you press each button. Resistor ladder switches give a different value for each button. A value out of range or one that jumps means the switch is worn.

Many of these switches mount near the airbag, so disconnect the battery and wait before removing them.

Check the Clockspring and Wiring

If the switch tests good, check the circuit through the clockspring to the PCM. Turn the steering wheel lock to lock while watching live data. A signal that drops out as you turn points to the clockspring.

How to Fix the P0568 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Replace a worn cruise switch.
  • Replace a failed clockspring.
  • Clean a corroded connector.
  • Repair damaged wiring.
  • Free a sticking button.

When replacing a clockspring, center it according to the service manual before you install it. A clockspring installed off center can break the first time you turn the wheel to full lock.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the PCM before testing the switch
  • Installing a clockspring off center
  • Removing the airbag without disconnecting the battery

What Repairs Cost

The cost to fix a P0568 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Connector cleaning$5 to $10$50 to $100
Cruise control switch$30 to $150$100 to $300
Clockspring$40 to $200$200 to $500
Brake light switch$10 to $50$75 to $200
Wiring repair$10 to $30$100 to $300

A switch or clockspring is usually the most costly part. Cleaning a sticky button costs nothing.

Is It Safe to Keep Driving with a P0568 Code?

Usually, yes. Cruise control may not work, but the engine, brakes and steering work as normal.

If the code involves the brake switch, check that your brake lights work. Drivers behind you need them, and some vehicles will not shift out of park or will limit power with a faulty brake switch.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0565Cruise Control On Signal Malfunction
P0566Cruise Control Off Signal Malfunction
P0567Cruise Control Resume Signal Malfunction
P0571Cruise Control/Brake Switch A Circuit Malfunction
P0575Cruise Control Input Circuit
P0500Vehicle Speed Sensor Malfunction
P0569Cruise Control Coast Signal
P0570Cruise Control Accel Signal

Fixing the Cruise Set Signal

A P0568 code means the PCM found a problem with the cruise set signal. Worn switches, failed clocksprings and corroded connectors cause most cases.

  • Watch the switch status in live data.
  • Check that the button moves freely.
  • Test the switch resistance.
  • Check the clockspring and wiring.

Frequently Asked Questions

Can I Drive with the P0568 Code?

Yes. The cruise control may not work, but the vehicle drives normally. Fix it when convenient, especially if other steering wheel buttons are also acting up, since that can point to a clockspring that also serves the airbag.

Can a Bad Clockspring Cause Cruise Control Codes?

Yes. The clockspring carries the steering wheel switch signals. When it wears out, the cruise buttons can stop working, often along with the horn, the airbag light or other steering wheel buttons. Replacing it needs care, since the airbag must be removed safely.

Why Does My Cruise Control Turn Off by Itself?

The PCM cancels cruise when it sees the brake switch change, a switch signal it does not trust or a vehicle speed problem. A misadjusted brake switch or worn steering wheel switch often causes it.

Is It Safe to Remove the Airbag Myself?

Only if you follow the service manual exactly. Disconnect the battery and wait the specified time, usually several minutes, before unplugging the airbag. Store it face up away from heat. If you are not comfortable doing this, have a shop do it.

Will the Cruise Control Code Affect Engine Performance?

Usually not. Most cruise switch codes only disable the cruise control. Brake switch codes are the exception, since the brake switch can also affect shifting and throttle control on some vehicles.

Can I Replace a Cruise Switch Myself?

Often, yes. Stalk switches usually come off with a few screws after removing the column covers. Steering wheel switches usually need the airbag removed first, so follow the service manual closely. Buy a switch that matches your vehicle’s part number, since resistor values differ between models.

Does Adaptive Cruise Use the Same Switches?

Usually, yes. Adaptive cruise uses the same or similar steering wheel buttons, plus a radar or camera that measures the distance to the car ahead. Switch codes like these can disable both normal and adaptive cruise. Radar or camera faults set different codes, often in another module.

Why Did the Code Appear After Cleaning the Interior?

Spray cleaners and water can get into steering wheel switches and their connectors. The liquid changes the resistance or shorts the contacts, so the PCM sees a wrong or stuck button. Let the switch dry fully, and spray cleaner onto a cloth instead of onto the switch next time.