P0575 Code: Meaning, Symptoms, Causes & Fixes

When none of the cruise buttons work, the problem is often the shared input circuit. A P0575 code means the engine computer found a problem with the cruise control input circuit.

This guide explains how the cruise input circuit works, what makes it fail and how to test it.

P0575 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
5Vehicle speed, idle control and auxiliary inputsThe fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control.
75Specific faultCruise Control Input Circuit

What the P0575 Code Means

The SAE J2012 standard defines the P0575 code as Cruise Control Input Circuit. On most vehicles, the powertrain control module (PCM) runs the cruise control. It reads the cruise switches on the steering wheel or stalk, the brake switch and vehicle speed, then holds speed by moving the electronic throttle. Older vehicles use a cable and a separate servo.

Many vehicles send all the cruise buttons to the PCM on one or two wires through a resistor ladder. Each button gives a different voltage, so the PCM can tell which one is pressed. On steering wheel switches, the signal passes through the clockspring, a coiled ribbon cable behind the steering wheel.

This code sets when the PCM sees a cruise input signal it does not trust, such as one that is out of range or does not match a valid button. Because the buttons often share one wire, a fault here can disable all of them.

Symptoms of a Cruise Input Circuit Fault

Most cruise faults only affect the cruise control. Common signs of a P0575 code include:

  • Cruise control not working
  • None of the cruise buttons responding
  • Cruise canceling by itself
  • Check engine light on some vehicles

Other steering wheel buttons, the horn or the airbag light acting up at the same time points to the clockspring.

Most Common Causes of the P0575 Code

These are the usual causes:

  1. Failed cruise switch. The resistor ladder inside fails.
  2. Water or spilled drink in the switch. Shorts the contacts.
  3. Failed clockspring. The ribbon cable breaks or shorts.
  4. Signal wire shorted to ground. In the column or under the dash.
  5. Corroded connector. Moisture raises resistance or creates a short.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II scan tool that shows cruise switch status
  • Digital multimeter
  • Wiring diagram for your vehicle
  • Trim tools for removing steering wheel covers
  • Contact cleaner

Step-By-Step Diagnosis of the P0575 Code

Watch the switch status in live data while you press each button. It is the quickest way to see what the PCM sees.

Watch the Input in Live Data

With the key on, watch the cruise input status or voltage in live data. With no button pressed, it should show a steady idle value. Press each button and note the change.

Unplug the Switch

Unplug the cruise switch and watch the reading again. If the fault clears, the switch is likely at fault. If it stays, the wiring or clockspring is the problem.

Test the Switch Resistance

Measure the switch resistance as you press each button and compare it with the service manual. A low value with no button pressed points to a shorted switch.

Disconnect the battery and wait before removing switches near the airbag.

Check the Clockspring and Wiring

Check the circuit through the clockspring to the PCM for continuity and for shorts to ground. Turn the wheel lock to lock while watching live data to catch a clockspring fault.

Repairs That Clear the P0575 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Replace a failed cruise switch.
  • Replace a failed clockspring.
  • Repair a shorted wire.
  • Clean and dry a wet connector.

When replacing a clockspring, center it according to the service manual before you install it. A clockspring installed off center can break the first time you turn the wheel to full lock.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing the PCM before testing the switch
  • Installing a clockspring off center
  • Removing the airbag without disconnecting the battery

What Repairs Cost

The cost to fix a P0575 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Connector cleaning$5 to $10$50 to $100
Cruise control switch$30 to $150$100 to $300
Clockspring$40 to $200$200 to $500
Brake light switch$10 to $50$75 to $200
Wiring repair$10 to $30$100 to $300

A cruise switch or clockspring is the most likely part needed. Labor is usually modest.

Can You Drive with a P0575 Code?

Usually, yes. Cruise control may not work, but the engine, brakes and steering work as normal.

If the code involves the brake switch, check that your brake lights work. Drivers behind you need them, and some vehicles will not shift out of park or will limit power with a faulty brake switch.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0565Cruise Control On Signal Malfunction
P0566Cruise Control Off Signal Malfunction
P0567Cruise Control Resume Signal Malfunction
P0568Cruise Control Set Signal Malfunction
P0571Cruise Control/Brake Switch A Circuit Malfunction
P0500Vehicle Speed Sensor Malfunction
P0572Cruise Control/Brake Switch A Circuit Low
P0573Cruise Control/Brake Switch A Circuit High
P0574Cruise Control System, Vehicle Speed Too High
P0576Cruise Control Input Circuit Low
P0578Cruise Control Multi-Function Input A Circuit Stuck
P0579Cruise Control Multi-Function Input A Circuit Range/Performance
P0580Cruise Control Multi-Function Input A Circuit Low

Fixing the Cruise Input Circuit

A P0575 code means the PCM found a problem with the cruise input circuit. Failed switches, failed clocksprings and wiring faults cause most cases.

  • Watch the input in live data.
  • Unplug the switch to isolate the fault.
  • Test the switch resistance.
  • Check the clockspring and wiring.

Frequently Asked Questions

Why Do All My Cruise Buttons Stop Working at Once?

On many vehicles, every cruise button shares one signal wire through a resistor ladder. A fault in that wire, the clockspring or the switch can disable all of them together.

Can a Bad Clockspring Cause Cruise Control Codes?

Yes. The clockspring carries the steering wheel switch signals. When it wears out, the cruise buttons can stop working, often along with the horn, the airbag light or other steering wheel buttons. Replacing it needs care, since the airbag must be removed safely.

Why Does My Cruise Control Turn Off by Itself?

The PCM cancels cruise when it sees the brake switch change, a switch signal it does not trust or a vehicle speed problem. A misadjusted brake switch or worn steering wheel switch often causes it.

Is It Safe to Remove the Airbag Myself?

Only if you follow the service manual exactly. Disconnect the battery and wait the specified time, usually several minutes, before unplugging the airbag. Store it face up away from heat. If you are not comfortable doing this, have a shop do it.

Will the Cruise Control Code Affect Engine Performance?

Usually not. Most cruise switch codes only disable the cruise control. Brake switch codes are the exception, since the brake switch can also affect shifting and throttle control on some vehicles.

Can I Replace a Cruise Switch Myself?

Often, yes. Stalk switches usually come off with a few screws after removing the column covers. Steering wheel switches usually need the airbag removed first, so follow the service manual closely. Buy a switch that matches your vehicle’s part number, since resistor values differ between models.

Does Adaptive Cruise Use the Same Switches?

Usually, yes. Adaptive cruise uses the same or similar steering wheel buttons, plus a radar or camera that measures the distance to the car ahead. Switch codes like these can disable both normal and adaptive cruise. Radar or camera faults set different codes, often in another module.

Why Did the Code Appear After Cleaning the Interior?

Spray cleaners and water can get into steering wheel switches and their connectors. The liquid changes the resistance or shorts the contacts, so the PCM sees a wrong or stuck button. Let the switch dry fully, and spray cleaner onto a cloth instead of onto the switch next time.