The brake switch does more than turn on the brake lights. It cancels cruise control and, on many vehicles, lets you shift out of park. A P0571 code means the engine computer found a problem in the brake switch A circuit.
This guide explains how the brake switch works, why it goes out of adjustment and how to test it.
P0571 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 5 | Vehicle speed, idle control and auxiliary inputs | The fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control. |
| 71 | Specific fault | Cruise Control/Brake Switch A Circuit Malfunction |
What the P0571 Code Means
The SAE J2012 standard defines the P0571 code as Cruise Control/Brake Switch A Circuit Malfunction. On most vehicles, the powertrain control module (PCM) runs the cruise control. It reads the cruise switches on the steering wheel or stalk, the brake switch and vehicle speed, then holds speed by moving the electronic throttle. Older vehicles use a cable and a separate servo.
Many vehicles send all the cruise buttons to the PCM on one or two wires through a resistor ladder. Each button gives a different voltage, so the PCM can tell which one is pressed. On steering wheel switches, the signal passes through the clockspring, a coiled ribbon cable behind the steering wheel.
The brake switch sits above the brake pedal arm. Many have two circuits. Brake switch A often feeds the brake lights and tells the PCM when the brakes are applied, and switch B is a second signal used to cross-check it. This general code sets when the PCM sees a brake switch signal it does not trust, such as one that does not change when it should or does not match brake switch B.
Symptoms of a Brake Switch Fault
Most cruise faults only affect the cruise control. Common signs of a P0571 code include:
- Cruise control not working or canceling
- Brake lights not working or staying on
- Shifter stuck in park
- Check engine light on
- Traction or stability light on some vehicles
Ask a helper to check the brake lights while you press the pedal. Brake lights that stay on all the time, or never come on, point straight at the switch or its circuit.
What Causes the P0571 Code?
These are the usual causes:
- Misadjusted brake switch. The pedal does not close or open it correctly.
- Failed brake switch. The contacts wear out.
- Blown fuse. The brake light or switch fuse.
- Broken pedal stop or bumper. A missing plastic stop lets the switch sit wrong. This is very common.
- Damaged wiring or connector. Near the pedal or in the rear lights.
- Burned-out brake bulbs. On some vehicles, the PCM checks the bulb circuit.
Tools You Will Need
You can do most of this testing at home with basic tools:
- OBD-II scan tool that shows cruise switch status
- Digital multimeter
- Wiring diagram for your vehicle
- Trim tools for removing steering wheel covers
- Contact cleaner
How to Track Down the P0571 Code
Watch the switch status in live data while you press each button. It is the quickest way to see what the PCM sees.
Check the Brake Lights
With a helper or a reflection in a window, check that all brake lights come on when you press the pedal and go off when you release it.
Watch the Switch in Live Data
With the key on, watch brake switch A and B status in live data while you press and release the pedal slowly. Both should change, at about the same point in pedal travel.
Inspect the Switch and Pedal Stop
Look at the brake switch above the pedal arm. Check that the plastic stop or bumper the switch presses against is in place. A broken or missing stop is a common cause.
Check that the switch is adjusted so it turns off when the pedal is released and on with a light press.
Test the Circuit
Check the brake light fuse. With the switch unplugged, check for power at the feed pin and continuity across the switch as you press the pedal. Follow the wiring diagram for your vehicle.
Repairs That Fix the P0571 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Adjust the brake switch so it turns on with light pedal pressure.
- Replace a failed brake switch.
- Replace a broken pedal stop or bumper.
- Replace a blown fuse after finding the cause.
- Repair damaged wiring.
- Replace burned-out brake bulbs.
Some brake switches self-adjust when you pull the pedal up after installing them. Others use a threaded body and locknut. Follow the service manual, and check the brake lights afterward.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing the switch when a pedal stop is broken
- Ignoring brake lights that stay on
- Forgetting to check the fuse
Typical Repair Costs
The cost to fix a P0571 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Connector cleaning | $5 to $10 | $50 to $100 |
| Cruise control switch | $30 to $150 | $100 to $300 |
| Clockspring | $40 to $200 | $200 to $500 |
| Brake light switch | $10 to $50 | $75 to $200 |
| Wiring repair | $10 to $30 | $100 to $300 |
A brake switch is cheap and quick to replace on most vehicles. A broken pedal stop costs only a few dollars.
Can You Drive with a P0571 Code?
Be careful. If the brake lights do not work, drivers behind you will not know when you are slowing down, which raises the risk of a rear-end crash.
Check the brake lights before driving. If they do not work, get the switch fixed right away.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0565 | Cruise Control On Signal Malfunction |
| P0566 | Cruise Control Off Signal Malfunction |
| P0567 | Cruise Control Resume Signal Malfunction |
| P0568 | Cruise Control Set Signal Malfunction |
| P0575 | Cruise Control Input Circuit |
| P0500 | Vehicle Speed Sensor Malfunction |
| P0570 | Cruise Control Accel Signal |
| P0572 | Cruise Control/Brake Switch A Circuit Low |
| P0573 | Cruise Control/Brake Switch A Circuit High |
| P0574 | Cruise Control System, Vehicle Speed Too High |
| P0576 | Cruise Control Input Circuit Low |
| P0578 | Cruise Control Multi-Function Input A Circuit Stuck |
| P0579 | Cruise Control Multi-Function Input A Circuit Range/Performance |
| P0580 | Cruise Control Multi-Function Input A Circuit Low |
Fixing the Brake Switch
A P0571 code means the PCM found a problem with the brake switch A circuit. Misadjusted switches, failed switches and broken pedal stops cause most cases.
- Check the brake lights.
- Watch brake switch status in live data.
- Inspect the switch and pedal stop.
- Test the fuse and circuit.
Frequently Asked Questions
Can a Bad Brake Switch Keep the Shifter in Park?
Yes. Many vehicles need a brake signal to release the shift interlock. If the switch fails, the shifter may not move out of park. Most have a manual release slot near the shifter for emergencies.
Can a Bad Clockspring Cause Cruise Control Codes?
Yes. The clockspring carries the steering wheel switch signals. When it wears out, the cruise buttons can stop working, often along with the horn, the airbag light or other steering wheel buttons. Replacing it needs care, since the airbag must be removed safely.
Why Does My Cruise Control Turn Off by Itself?
The PCM cancels cruise when it sees the brake switch change, a switch signal it does not trust or a vehicle speed problem. A misadjusted brake switch or worn steering wheel switch often causes it.
Is It Safe to Remove the Airbag Myself?
Only if you follow the service manual exactly. Disconnect the battery and wait the specified time, usually several minutes, before unplugging the airbag. Store it face up away from heat. If you are not comfortable doing this, have a shop do it.
Will the Cruise Control Code Affect Engine Performance?
Usually not. Most cruise switch codes only disable the cruise control. Brake switch codes are the exception, since the brake switch can also affect shifting and throttle control on some vehicles.
Can I Replace a Cruise Switch Myself?
Often, yes. Stalk switches usually come off with a few screws after removing the column covers. Steering wheel switches usually need the airbag removed first, so follow the service manual closely. Buy a switch that matches your vehicle’s part number, since resistor values differ between models.
Does Adaptive Cruise Use the Same Switches?
Usually, yes. Adaptive cruise uses the same or similar steering wheel buttons, plus a radar or camera that measures the distance to the car ahead. Switch codes like these can disable both normal and adaptive cruise. Radar or camera faults set different codes, often in another module.
Why Did the Code Appear After Cleaning the Interior?
Spray cleaners and water can get into steering wheel switches and their connectors. The liquid changes the resistance or shorts the contacts, so the PCM sees a wrong or stuck button. Let the switch dry fully, and spray cleaner onto a cloth instead of onto the switch next time.