A speed signal that drops out for a moment can cause a harsh shift and come back on its own. A P0718 code means the transmission computer caught the input speed sensor signal dropping out or jumping.
This guide explains what the input speed sensor does, why it fails and how to test it step by step.
P0718 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine or transmission systems. |
| 0 | Generic (SAE) code | The definition is the same on every OBD-II vehicle. |
| 7 | Transmission | The fault involves the transmission, such as its sensors, solenoids, gear ratios or the torque converter clutch. |
| 18 | Specific fault | Input/Turbine Speed Sensor Circuit Intermittent |
What the P0718 Code Means
The SAE J2012 standard defines the P0718 code as Input/Turbine Speed Sensor Circuit Intermittent. The input speed sensor, also called the turbine speed sensor, reads how fast the transmission input shaft spins. That is the speed of the torque converter turbine. It usually mounts on the transmission case near the front and reads a toothed ring on a drum or the input shaft.
The computer compares input speed with output speed to work out the gear ratio and shift quality, and with engine speed to work out torque converter slip. Most of these sensors are either two-wire magnetic sensors that make their own AC voltage, or three-wire Hall effect sensors that need a power feed and send a square wave.
When the computer loses a speed signal, it usually cannot shift smoothly, so it often switches to limp mode and holds one gear.
Intermittent means the input speed sensor signal dropped out or jumped for short moments, faster than the real condition could change. The fault may last only a fraction of a second, so the circuit often tests fine when parked.
Symptoms of a Faulty Input Speed Sensor
A bad speed signal usually changes how the transmission shifts. Common signs of a P0718 code include:
- Check engine light on
- Harsh or erratic shifts
- Transmission stuck in one gear or limp mode
- Speedometer not working on some vehicles
- Torque converter not locking up
Many transmissions go into limp mode, often holding second or third gear, when a speed signal is lost. Clearing the code may bring normal shifting back until the fault returns.
What Causes the P0718 Code?
Anything that breaks the circuit for an instant can set this code:
- Loose connector. A connector that is not fully locked loses contact with engine movement.
- Spread or corroded terminals. Weak pins lose grip as they heat up.
- Chafed wiring. Insulation wears through where wires rub on brackets.
- Broken wire inside the insulation. The copper separates only when flexed.
- Failing input speed sensor. Internal faults can come and go with heat.
- Moisture in the connector. A worn seal lets water in during rain or washing.
Tools You Will Need
You can do most of this testing at home with basic tools:
- Transmission scan tool that shows input, output and engine speed
- Digital multimeter or lab scope
- Jack stands
- Wiring diagram for your transmission
- Clean rag and brake cleaner for the sensor tip
Step-By-Step Diagnosis of the P0718 Code
Check the fluid level first, then find the sensor using your service manual. Some are external, and some sit inside the transmission.
Check Live Data
Drive the vehicle, or raise the drive wheels safely on jack stands, and watch the input speed sensor reading in live data. It should rise smoothly with speed. A reading of zero, or one that drops out or jumps, confirms the fault.
Graph the Signal and Wiggle the Wiring
Graph the input speed sensor signal with the engine running. Gently wiggle the connector, then the wiring one section at a time. A sudden spike or drop marks the bad spot. Tap the sensor body lightly too.
Inspect the Connector
Turn the engine off and unplug the connector. Look for corrosion, spread pins, a broken lock and water inside. Check the engine ground straps if several sensors glitch at the same time.
Check the Fluid Level
Check the transmission fluid level and condition with the procedure in your service manual. Low or burnt fluid can cause slipping that upsets the speed readings.
How to Fix the P0718 Code
Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.
- Clean the sensor tip and reinstall it with a new O-ring.
- Repair the connector or wiring.
- Replace the input speed sensor if it fails tests.
- Correct the fluid level.
- Program the correct tire size if it was changed.
After the repair, clear the codes and drive through every gear. Some transmissions need a relearn to restore normal shift feel after a limp mode event.
Common Mistakes to Avoid
These mistakes waste money or leave the real fault in place:
- Replacing parts when the circuit tests fine at rest
- Not graphing the signal while wiggling the wiring
- Replacing the sensor before checking the connector
- Ignoring metal debris that points to internal wear
What Repairs Cost
The cost to fix a P0718 code depends on the cause. This table shows typical ranges for parts and labor.
| Repair | DIY Cost | Typical Shop Cost |
|---|---|---|
| Connector cleaning or repair | $10 to $30 | $75 to $250 |
| Wiring repair | $10 to $40 | $100 to $300 |
| Speed sensor | $20 to $100 | $100 to $350 |
| Internal sensor access | $20 to $60 in fluid | $200 to $500 |
| Transmission control module | $150 to $500 | $400 to $1,000 |
External speed sensors are usually cheap and easy to replace. Internal ones need the pan or more removed, which adds labor.
Is It Safe to Keep Driving with a P0718 Code?
Drive only as far as you need to. Many transmissions go into limp mode with this code, which limits acceleration and top speed.
Erratic shifts can make merging and passing harder. Driving a long way in limp mode can also overheat the transmission.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P0715 | Input/Turbine Speed Sensor Circuit Malfunction |
| P0716 | Input/Turbine Speed Sensor Circuit Range/Performance |
| P0717 | Input/Turbine Speed Sensor Circuit No Signal |
| P0700 | Transmission Control System Malfunction |
| P0730 | Incorrect Gear Ratio |
| P0500 | Vehicle Speed Sensor Malfunction |
| P0719 | Brake Switch B Circuit Low |
Fixing the Input Speed Sensor
A P0718 code means the input speed sensor signal drops out or jumps. Loose connectors and chafed wiring cause most cases.
- Check the fluid level.
- Watch the speed readings in live data.
- Inspect and clean the sensor.
- Test the wiring and replace the sensor if needed.
Frequently Asked Questions
Why Does the P0718 Code Come and Go?
Heat and vibration can make a weak connection or a failing sensor drop out for a moment. The fault often appears only after the transmission warms up. Wiggle testing the wiring while watching live data helps find it.
What Is Limp Mode?
Limp mode is a protection strategy. When the computer cannot trust a sensor, it holds one gear, often second or third, and may raise line pressure. You can drive slowly to a repair shop, but acceleration and top speed are limited.
Are the Input and Output Speed Sensors the Same Part?
Sometimes they look alike, but they often have different part numbers and connectors. Check the parts catalog for your transmission before you buy one.
Can Low Transmission Fluid Cause Sensor Codes?
Sometimes. Low fluid makes the transmission slip and run hot, which can upset speed and temperature readings and set range codes. Check the fluid level with the procedure in your service manual before you replace a sensor.
Does the Transmission Need a Relearn After a Sensor Repair?
Some do. Many modern transmissions store learned shift data, and a few need a relearn or a reset after a sensor or wiring repair. Check the service manual, especially if shifts feel odd after the fix.
Where Is the Transmission Computer?
On some vehicles, the PCM controls the transmission. On others, a separate transmission control module (TCM) sits under the dash, in the engine bay or bolted inside the transmission. Your service manual shows which one your vehicle uses.
Can I Check the Transmission Fluid Myself?
On many older vehicles, yes, with the dipstick and the engine running in park at operating temperature. Many newer transmissions have no dipstick and are checked at a fill plug with the fluid at a set temperature, often with a scan tool to read it. Follow the procedure for your transmission.
Should I Fix Electrical Codes Before Mechanical Ones?
Yes. A sensor or wiring fault can make the computer shift badly, use limp mode or misjudge gear ratio, which may set other codes that look mechanical. Fix the electrical faults first, clear the codes and see which ones come back.