The P1106 code is a manufacturer-specific code, so its meaning depends on who built your vehicle. On Ford it points to the charging and power supply, on GM it points to the MAP and BARO sensors and on Honda it points to the MAP and BARO sensors. Each maker uses its own definition and its own test steps.
This guide explains the meaning for each make, the symptoms and causes you can expect on each one, and how to track down the real fault before you spend money on parts.
P1106 Code Breakdown
Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. The second character tells you whether the definition is shared by every maker or set by the carmaker itself. This table shows what each part of the code tells you.
| Character | Meaning | What It Tells You |
|---|---|---|
| P | Powertrain | The fault is in the engine, transmission or driveline systems. |
| 1 | Manufacturer-specific code | The carmaker sets the definition, so the same code can mean different things on different brands. |
| 1 | Fuel and air metering | The fault involves fuel and air metering, such as airflow, temperature, throttle and oxygen sensors or fuel control. |
| 06 | Specific fault | Set by each maker. See the table below for the makes that use it. |
What the P1106 Code Means by Make
Find your make in the table first, then read its section below. The definitions come from published factory code lists for each maker. Some makers changed a code’s meaning between model years, so confirm it with a scan tool set to your exact vehicle.
| Make | Definition | System Involved |
|---|---|---|
| Ford, Lincoln and Mercury | Dual Alternator Lower Fault | Charging and power supply |
| GM (Chevrolet, GMC, Buick, Cadillac, Pontiac, Oldsmobile, Saturn) | MAP sensor circuit voltage intermittent high or low | MAP and BARO sensors |
| Honda and Acura | Barometric Pressure Circuit Range/Performance | MAP and BARO sensors |
| Volkswagen, Audi, Seat and Skoda | Bank 2 sensor 1 O2 signal reads too low, likely from an air leak (VAG fault 17514) | Oxygen sensor |
| Subaru | Engine Torque Control Signal 2 Circuit Malfunction | Traction control and torque request |
| Isuzu | MAP Circuit Intermittent Voltage High | MAP and BARO sensors |
| Other makes | No confirmed definition | Check with a scan tool set to your make |
Ford, Lincoln and Mercury: Charging and Power Supply
On Ford, Lincoln and Mercury vehicles, this code is listed as Dual Alternator Lower Fault. The engine computer monitors system voltage and, on many vehicles, controls the alternator output directly. It also watches its own power feeds and relays. A code here means a voltage it sees is too high or too low, or a control circuit to the alternator or a relay has failed.
When the Computer Flags the Charging and Power Supply
The computer found a problem in the charging and power supply circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.
Charging and Power Supply Symptoms
- Check engine light or battery light on.
- Dim or flickering lights.
- Slow cranking or a dead battery.
- Stalling or several warning lights at once.
Charging and Power Supply Causes
- Damaged connector or wire.
- Failed part in the charging and power supply.
- Blown fuse or failed relay in the feed circuit.
- Weak battery or corroded battery terminals.
- Failed alternator or voltage regulator.
How to Test the Charging and Power Supply
Unplug the part and measure its resistance against the specification. With the key on, check for battery voltage on the feed wire. Then check the control wire for continuity back to the computer and for any short to ground or to voltage. A scan tool that can command the part on and off makes this faster.
Test the battery, then measure charging voltage at the battery with the engine running. It should be about 13.5 to 14.8 volts. Check the alternator belt and connectors. Perform a voltage drop test on the main power and ground cables while cranking and while running with loads on.
Charging and Power Supply Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the failed part in the charging and power supply only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Charging and Power Supply Mistakes to Avoid
- Replacing the alternator before testing the battery, the belt and the main cables.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
GM, Honda and Isuzu: MAP and BARO Sensors
These makers all use this number for a fault in the MAP and BARO sensors, but each words it differently:
- GM (Chevrolet, GMC, Buick, Cadillac, Pontiac, Oldsmobile, Saturn): MAP sensor circuit voltage intermittent high or low.
- Honda and Acura: Barometric Pressure Circuit Range/Performance.
- Isuzu: MAP Circuit Intermittent Voltage High.
The manifold absolute pressure (MAP) sensor reads intake manifold pressure, which tells the computer how much load is on the engine. The barometric (BARO) sensor, or a BARO reading taken by the MAP sensor at key-on, tells it the outside air pressure. Some engines switch one sensor between the two with a solenoid valve.
When the Computer Flags the MAP and BARO Sensors
On GM and Isuzu: the computer saw the MAP and BARO sensors signal drop out or jump for a short time and then come back. Intermittent codes almost always point to a loose connector pin, a chafed wire or a part that fails only when hot or cold.
On Honda: range or performance means the MAP and BARO sensors circuit works electrically, but the reading or result does not make sense for the conditions, or does not agree with related sensors. The part may be worn, sticking or reporting a real problem elsewhere.
MAP and BARO Sensors Symptoms
- Check engine light on.
- Hesitation, rough idle or poor power.
- Black smoke or poor fuel economy if the reading is too high.
- Hard starting.
MAP and BARO Sensors Causes
- Loose connector pin or corrosion.
- Wire chafed against a bracket or hot part.
- Part that fails only when hot or cold.
- Cracked, loose or plugged vacuum hose to the MAP sensor.
- Failed MAP or BARO sensor.
- Vacuum leak that raises manifold pressure at idle.
- Shorted 5-volt reference from another sensor on the same circuit.
How to Test the MAP and BARO Sensors
Back-probe the connector with the key on. You should see about 5 volts on the reference wire, a good ground on the ground wire, and a signal that changes smoothly as the part moves or the pressure changes. A signal stuck near 0 or 5 volts points to a short or an open.
With the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level. At warm idle, manifold vacuum should be about 18 to 21 inches. Check the vacuum hose for cracks and blockage, and apply vacuum with a hand pump to see the reading change smoothly.
MAP and BARO Sensors Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the failed part in the MAP and BARO sensors only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
MAP and BARO Sensors Mistakes to Avoid
- Replacing the sensor without checking its vacuum hose.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Volkswagen, Audi, Seat and Skoda: Oxygen Sensor
On Volkswagen, Audi, Seat and Skoda vehicles, this code is listed as Bank 2 sensor 1 O2 signal reads too low, likely from an air leak (VAG fault 17514). Oxygen sensors in the exhaust tell the engine computer whether the mixture is rich or lean. The front sensor is used for fuel control and switches quickly once the engine is warm. The rear sensor watches the catalytic converter. Some newer engines use a wide-band air-fuel sensor that reads the exact mixture.
What Sets the Oxygen Sensor Fault
Range or performance means the oxygen sensor circuit works electrically, but the reading or result does not make sense for the conditions, or does not agree with related sensors. The part may be worn, sticking or reporting a real problem elsewhere.
Oxygen Sensor Symptoms
- Check engine light on.
- Higher fuel use.
- Rough idle or hesitation in some cases.
- Failed emissions test.
Oxygen Sensor Causes
- Worn or contaminated oxygen sensor.
- Exhaust leak ahead of the sensor that lets in outside air.
- Vacuum leak or fuel pressure problem that really is making the mixture lean or rich.
- Misfire that sends unburned oxygen past the sensor.
- Sensor wires swapped after a repair.
- Damaged connector or wiring.
How to Test the Oxygen Sensor
Warm the engine fully and watch the sensor in live data. A front sensor should switch between about 0.1 and 0.9 volts several times a second at 2,000 rpm. A lazy or stuck reading points to the sensor. A reading that stays lean along with high positive fuel trim points to a real lean condition, so look for vacuum and exhaust leaks before you replace the sensor.
If the readings point to a part, check its connector and wiring before you replace it, since a poor connection can cause the same result.
Oxygen Sensor Repairs
- Fix the cause the tests point to, starting with the simplest one: worn or contaminated oxygen sensor.
- Replace the oxygen sensor only if testing confirms it is at fault.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Oxygen Sensor Mistakes to Avoid
- Replacing the oxygen sensor before checking for vacuum and exhaust leaks.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Subaru: Traction Control and Torque Request
On Subaru vehicles, this code is listed as Engine Torque Control Signal 2 Circuit Malfunction. The ABS or traction control module asks the engine computer to cut torque when a wheel spins. The engine computer answers with a torque signal. These requests travel over a dedicated wire or the data network, and a code sets when the signal is missing or out of range.
When the Computer Flags the Traction Control and Torque Request
The computer found a problem in the traction control and torque request circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.
Traction Control and Torque Request Symptoms
- Traction control or ABS light on.
- Check engine light on.
- Traction control not working or cutting power when it should not.
Traction Control and Torque Request Causes
- Damaged connector or wire.
- Failed part in the traction control and torque request.
- Blown fuse or failed relay in the feed circuit.
- Fault stored in the ABS or traction control module.
- Failed wheel speed sensor.
How to Test the Traction Control and Torque Request
Check battery voltage, fuses and grounds first. Then check the power, ground and signal wires at the part or module named in the code, and scan the other modules for related codes.
Read codes in the ABS and traction control modules first, since this code is often a result of a fault there. Check the wheel speed sensors in live data on a test drive, then check the torque signal wiring between the modules.
Traction Control and Torque Request Repairs
- Clean, reseat or replace the connector if the pins are loose, bent or corroded.
- Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
- Replace the failed part in the traction control and torque request only if it fails the resistance, voltage or live data test.
- Clear the code and drive through the same conditions that set it to confirm the repair.
Traction Control and Torque Request Mistakes to Avoid
- Working on the engine computer before reading the codes in the ABS module.
- Trusting a code definition that belongs to another maker.
- Clearing the code without fixing the cause and hoping it stays off.
Other Makes
We could not confirm a definition for Toyota, Nissan, Chrysler, Hyundai, Kia, Mazda, BMW or Mercedes-Benz. If your scanner shows the P1106 code on one of those makes, read it again with a scan tool set to the exact make, model and year, or check the factory service information. A generic code reader may show the Ford meaning for every vehicle, which can send you after the wrong part.
How to Confirm Which Meaning Applies to Your Vehicle
A code number alone is not enough on manufacturer-specific codes. Use these steps to make sure you are chasing the right fault.
- Pick the correct make and model in your scan tool, so it uses that maker’s code library.
- Write down the full description the tool shows, plus any other codes stored with it.
- Use the freeze frame data to see when the fault set, such as cold start, idle or highway speed.
- Match the code with the service information for your exact engine and model year.
- If two sources disagree, trust the one tied to your VIN, such as a dealer or a factory repair manual.
Tools You Will Need
- OBD-II scan tool with live data and a make-specific code library.
- Digital multimeter.
- Spare relay of the same type for swap tests.
- Hand vacuum pump.
- Lab scope or graphing meter (helpful for signal checks).
- Oxygen sensor socket.
- Wiring diagram for your exact model.
Repair Cost Breakdown
Costs depend on which maker’s meaning applies to your vehicle. These are typical ranges for parts and shop labor.
| Repair | Make | Typical Cost |
|---|---|---|
| Clean and reseat the connector | All | $0 to $60 |
| Replace the battery, alternator or relay | Ford | $100 to $700 |
| Replace the MAP or BARO sensor | GM, Honda, Isuzu | $40 to $250 |
| Replace the oxygen sensor | VW/Audi | $100 to $400 |
| Fix the ABS or traction control fault | Subaru | $100 to $500 |
| Repair a damaged wire | All | $80 to $250 |
Is It Safe to Drive with a P1106 Code?
It depends on which meaning applies to your vehicle. On GM, Honda, VW/Audi and Isuzu vehicles, short trips are usually fine, but fuel use, emissions or comfort may suffer until you fix it. On Ford vehicles, drive gently and get it checked soon, because the battery can go flat and leave you stranded. On Subaru vehicles, drive gently and get it checked soon, because traction control may not work on slippery roads. Stop driving if the check engine light starts flashing, the engine overheats or the vehicle loses power on the road.
When to See a Shop
Some of the checks in this guide need more than a meter. Module programming, transmission tests and key or immobilizer work usually need a dealer-level scan tool. If the basic checks for Subaru come back clean, a shop with factory software for your make can run the guided tests and confirm the fault before parts are replaced.
Related Codes
These codes often show up with this one or point to the same system:
| Code | Meaning |
|---|---|
| P1105 | Dual Alternator Upper Fault |
| P1107 | Dual Alternator Lower Circuit Malfunction |
| P1108 | Dual Alternator Battery Lamp Circuit Malfunction |
| P1244 | Alternator Load Input Failed High |
| P1245 | Alternator Load Input Failed Low |
| P1246 | Alternator Load Input Failed |
Fixing the P1106 Code
The fix for a P1106 code depends on the make, so confirm the meaning first.
- Ford: test the battery, then measure charging voltage at the battery with the engine running.
- GM: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
- Honda: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
- VW/Audi: warm the engine fully and watch the sensor in live data.
- Subaru: read codes in the ABS and traction control modules first, since this code is often a result of a fault there.
- Isuzu: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
- Any make: repair wiring and connectors before you replace a part.
Frequently Asked Questions
Why Does My Scanner Show a Different Meaning for This Code?
Basic code readers often show one maker’s definition for every manufacturer-specific code. Because P1 codes belong to each carmaker, the P1106 code on one brand is not the same fault as on another. A scan tool set to your exact make gives the right meaning.
Can a Weak Battery Set Engine Computer Codes?
Yes. Low voltage during cranking or driving can set power supply, communication and sensor codes all at once. Test and charge the battery before you chase the other codes.
How Do I Test a Three-Wire Sensor?
With the key on, check for about 5 volts on the reference wire and a good ground on the ground wire. Then watch the signal voltage change as the pressure or position changes.
Should I Replace the Oxygen Sensor Right Away?
Not until you rule out vacuum leaks, exhaust leaks and fuel pressure problems. Oxygen sensors often report a real mixture problem correctly, and a new sensor will set the same code if the real cause is still there.
Can I Just Clear the P1106 Code?
You can, but it returns if the fault is still there. Clearing the P1106 code also resets the readiness monitors, so the vehicle needs a few days of normal driving before it can pass an emissions test.