P1107 Code: Meaning, Symptoms, Causes & Fixes

The P1107 code is a manufacturer-specific code, so its meaning depends on who built your vehicle. On Ford it points to the charging and power supply, on GM it points to the MAP and BARO sensors and on Honda it points to the MAP and BARO sensors. Each maker uses its own definition and its own test steps.

This guide explains the meaning for each make, the symptoms and causes you can expect on each one, and how to track down the real fault before you spend money on parts.

P1107 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. The second character tells you whether the definition is shared by every maker or set by the carmaker itself. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine, transmission or driveline systems.
1Manufacturer-specific codeThe carmaker sets the definition, so the same code can mean different things on different brands.
1Fuel and air meteringThe fault involves fuel and air metering, such as airflow, temperature, throttle and oxygen sensors or fuel control.
07Specific faultSet by each maker. See the table below for the makes that use it.

What the P1107 Code Means by Make

Find your make in the table first, then read its section below. The definitions come from published factory code lists for each maker. Some makers changed a code’s meaning between model years, so confirm it with a scan tool set to your exact vehicle.

MakeDefinitionSystem Involved
Ford, Lincoln and MercuryDual Alternator Lower Circuit MalfunctionCharging and power supply
GM (Chevrolet, GMC, Buick, Cadillac, Pontiac, Oldsmobile, Saturn)MAP sensor voltage intermittent lowMAP and BARO sensors
Honda and AcuraBarometric Pressure Circuit Low InputMAP and BARO sensors
Volkswagen, Audi, Seat and SkodaBank 2 sensor 1 O2 heater circuit shorted to battery voltage (VAG fault 17515)Oxygen sensor heater
IsuzuMAP Circuit Intermittent Voltage LowMAP and BARO sensors
Other makesNo confirmed definitionCheck with a scan tool set to your make

Ford, Lincoln and Mercury: Charging and Power Supply

On Ford, Lincoln and Mercury vehicles, this code is listed as Dual Alternator Lower Circuit Malfunction. The engine computer monitors system voltage and, on many vehicles, controls the alternator output directly. It also watches its own power feeds and relays. A code here means a voltage it sees is too high or too low, or a control circuit to the alternator or a relay has failed.

What Sets the Charging and Power Supply Fault

The computer found a problem in the charging and power supply circuit or its operation. The code does not say exactly which part of the circuit failed, so start with the connector and wiring.

Charging and Power Supply Symptoms

  • Check engine light or battery light on.
  • Dim or flickering lights.
  • Slow cranking or a dead battery.
  • Stalling or several warning lights at once.

Charging and Power Supply Causes

  • Damaged connector or wire.
  • Failed part in the charging and power supply.
  • Blown fuse or failed relay in the feed circuit.
  • Weak battery or corroded battery terminals.
  • Failed alternator or voltage regulator.

How to Test the Charging and Power Supply

Unplug the part and measure its resistance against the specification. With the key on, check for battery voltage on the feed wire. Then check the control wire for continuity back to the computer and for any short to ground or to voltage. A scan tool that can command the part on and off makes this faster.

Test the battery, then measure charging voltage at the battery with the engine running. It should be about 13.5 to 14.8 volts. Check the alternator belt and connectors. Perform a voltage drop test on the main power and ground cables while cranking and while running with loads on.

Charging and Power Supply Repairs

  1. Clean, reseat or replace the connector if the pins are loose, bent or corroded.
  2. Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
  3. Replace the failed part in the charging and power supply only if it fails the resistance, voltage or live data test.
  4. Clear the code and drive through the same conditions that set it to confirm the repair.

Charging and Power Supply Mistakes to Avoid

  • Replacing the alternator before testing the battery, the belt and the main cables.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

GM, Honda and Isuzu: MAP and BARO Sensors

These makers all use this number for a fault in the MAP and BARO sensors, but each words it differently:

  • GM (Chevrolet, GMC, Buick, Cadillac, Pontiac, Oldsmobile, Saturn): MAP sensor voltage intermittent low.
  • Honda and Acura: Barometric Pressure Circuit Low Input.
  • Isuzu: MAP Circuit Intermittent Voltage Low.

The manifold absolute pressure (MAP) sensor reads intake manifold pressure, which tells the computer how much load is on the engine. The barometric (BARO) sensor, or a BARO reading taken by the MAP sensor at key-on, tells it the outside air pressure. Some engines switch one sensor between the two with a solenoid valve.

When the Computer Flags the MAP and BARO Sensors

On GM and Isuzu: the computer saw the MAP and BARO sensors signal drop out or jump for a short time and then come back. Intermittent codes almost always point to a loose connector pin, a chafed wire or a part that fails only when hot or cold.

On Honda: low input means the MAP and BARO sensors signal dropped below the expected range. A shorted sensor, a signal wire touching ground or a missing reference voltage can all cause it.

MAP and BARO Sensors Symptoms

  • Check engine light on.
  • Hesitation, rough idle or poor power.
  • Black smoke or poor fuel economy if the reading is too high.
  • Hard starting.

MAP and BARO Sensors Causes

  • Loose connector pin or corrosion.
  • Wire chafed against a bracket or hot part.
  • Part that fails only when hot or cold.
  • Signal wire shorted to ground.
  • Shorted part in the MAP and BARO sensors.
  • Missing reference voltage.
  • Cracked, loose or plugged vacuum hose to the MAP sensor.

How to Test the MAP and BARO Sensors

Back-probe the connector with the key on. You should see about 5 volts on the reference wire, a good ground on the ground wire, and a signal that changes smoothly as the part moves or the pressure changes. A signal stuck near 0 or 5 volts points to a short or an open.

With the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level. At warm idle, manifold vacuum should be about 18 to 21 inches. Check the vacuum hose for cracks and blockage, and apply vacuum with a hand pump to see the reading change smoothly.

MAP and BARO Sensors Repairs

  1. Clean, reseat or replace the connector if the pins are loose, bent or corroded.
  2. Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
  3. Replace the failed part in the MAP and BARO sensors only if it fails the resistance, voltage or live data test.
  4. Clear the code and drive through the same conditions that set it to confirm the repair.

MAP and BARO Sensors Mistakes to Avoid

  • Replacing the sensor without checking its vacuum hose.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

Volkswagen, Audi, Seat and Skoda: Oxygen Sensor Heater

On Volkswagen, Audi, Seat and Skoda vehicles, this code is listed as Bank 2 sensor 1 O2 heater circuit shorted to battery voltage (VAG fault 17515). Each heated oxygen sensor has a heating element inside it. The heater brings the sensor up to working temperature quickly after a cold start, so the engine can switch to closed-loop fuel control sooner. The engine computer switches the heater and checks the current it draws.

What Sets the Oxygen Sensor Heater Fault

A short to battery voltage means the oxygen sensor heater control wire sees voltage when the computer expects it to be pulled low, so the computer cannot switch it. This is often a chafed wire touching a powered circuit, or a shorted coil inside the part.

Oxygen Sensor Heater Symptoms

  • Check engine light on.
  • Longer warm-up before closed-loop fuel control.
  • Higher fuel use on short trips.
  • Possible failed emissions test.

Oxygen Sensor Heater Causes

  • Wire chafed and touching a powered circuit.
  • Shorted oxygen sensor heater.
  • Heater element burned out inside the sensor.
  • Blown heater fuse or failed heater relay.

How to Test the Oxygen Sensor Heater

Unplug the part and measure its resistance against the specification. With the key on, check for battery voltage on the feed wire. Then check the control wire for continuity back to the computer and for any short to ground or to voltage. A scan tool that can command the part on and off makes this faster.

Unplug the sensor and measure across the two heater pins on the sensor side. Most heaters read a few ohms. An open reading means the heater is burned out, and a reading near zero means it is shorted. With the key on, check for battery voltage on the heater feed wire at the connector, and check the fuse that feeds it.

Oxygen Sensor Heater Repairs

  1. Clean, reseat or replace the connector if the pins are loose, bent or corroded.
  2. Repair any chafed or broken wire with solder and heat shrink, and secure it away from heat and moving parts.
  3. Replace the oxygen sensor heater only if it fails the resistance, voltage or live data test.
  4. Clear the code and drive through the same conditions that set it to confirm the repair.

Oxygen Sensor Heater Mistakes to Avoid

  • Replacing the part without checking its fuse, power feed and control wire.
  • Trusting a code definition that belongs to another maker.
  • Clearing the code without fixing the cause and hoping it stays off.

Other Makes

We could not confirm a definition for Toyota, Nissan, Chrysler, Hyundai, Kia, Mazda, Subaru, BMW or Mercedes-Benz. If your scanner shows the P1107 code on one of those makes, read it again with a scan tool set to the exact make, model and year, or check the factory service information. A generic code reader may show the Ford meaning for every vehicle, which can send you after the wrong part.

How to Confirm Which Meaning Applies to Your Vehicle

Because the same number means different things on different makes, confirm the meaning before you buy parts.

  • Set your scan tool to the exact make, model, year and engine before you read codes.
  • Read the full code description on the tool, not just the number.
  • Check freeze frame data to see the engine speed, temperature and load when the code set.
  • Look up the code in the factory service information or a repair database for your exact vehicle.
  • Ask a dealer parts or service desk to confirm the meaning for your VIN if you are still unsure.

Tools You Will Need

  • OBD-II scan tool with live data and a make-specific code library.
  • Digital multimeter.
  • Spare relay of the same type for swap tests.
  • Hand vacuum pump.
  • Test light or noid light.
  • Oxygen sensor socket.

Repair Cost Breakdown

Costs depend on which maker’s meaning applies to your vehicle. These are typical ranges for parts and shop labor.

RepairMakeTypical Cost
Clean and reseat the connectorAll$0 to $60
Replace the battery, alternator or relayFord$100 to $700
Replace the MAP or BARO sensorGM, Honda, Isuzu$40 to $250
Replace the oxygen sensorVW/Audi$100 to $400
Repair a damaged wireAll$80 to $250

Is It Safe to Drive with a P1107 Code?

It depends on which meaning applies to your vehicle. On GM, Honda, VW/Audi and Isuzu vehicles, short trips are usually fine, but fuel use, emissions or comfort may suffer until you fix it. On Ford vehicles, drive gently and get it checked soon, because the battery can go flat and leave you stranded. Stop driving if the check engine light starts flashing, the engine overheats or the vehicle loses power on the road.

When to See a Shop

Most of the checks in this guide need only a scan tool with live data, a multimeter and some patience. See a shop if the wiring is buried somewhere hard to reach, if the code keeps coming back after the obvious fixes, or if the engine runs badly enough that driving to the shop is a risk. Bring the full code description, the freeze frame data and a list of what you have already tested, so the shop does not repeat the same steps.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P1106Dual Alternator Lower Fault
P1108Dual Alternator Battery Lamp Circuit Malfunction
P1105Dual Alternator Upper Fault
P1244Alternator Load Input Failed High
P1245Alternator Load Input Failed Low
P1246Alternator Load Input Failed

Fixing the P1107 Code

The fix for a P1107 code depends on the make, so confirm the meaning first.

  • Ford: test the battery, then measure charging voltage at the battery with the engine running.
  • GM: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
  • Honda: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
  • VW/Audi: unplug the sensor and measure across the two heater pins on the sensor side.
  • Isuzu: with the key on and the engine off, the MAP and BARO readings should both match the local air pressure, about 29 to 30 inches of mercury or 100 kPa near sea level.
  • Any make: repair wiring and connectors before you replace a part.

Frequently Asked Questions

Why Does My Scanner Show a Different Meaning for This Code?

Basic code readers often show one maker’s definition for every manufacturer-specific code. Because P1 codes belong to each carmaker, the P1107 code on one brand is not the same fault as on another. A scan tool set to your exact make gives the right meaning.

Can a Weak Battery Set Engine Computer Codes?

Yes. Low voltage during cranking or driving can set power supply, communication and sensor codes all at once. Test and charge the battery before you chase the other codes.

How Do I Test a Three-Wire Sensor?

With the key on, check for about 5 volts on the reference wire and a good ground on the ground wire. Then watch the signal voltage change as the pressure or position changes.

Can I Drive with a Bad Oxygen Sensor Heater?

Yes, for a short time. The engine runs in open loop longer after each cold start, so fuel use and emissions go up. The sensor heater is built into the sensor, so the fix is usually a new oxygen sensor.

Will the P1107 Code Come Back After Clearing It?

If the fault is still there, yes. The computer retests the system on every drive. After a real fix, the light stays off and the stored P1107 code erases itself after a number of clean drive cycles. Clearing it with a scan tool also resets the readiness monitors, so drive for a few days before an emissions test.