P0574 Code: Meaning, Symptoms, Causes & Fixes

Cruise control has a top speed it will not go past. A P0574 code means the engine computer saw vehicle speed go above the highest speed allowed for cruise control.

This guide explains why the code sets, when it is normal and how to check whether a speed sensor fault is to blame.

P0574 Code Breakdown

Every OBD-II code follows the same five-character pattern set by the SAE J2012 standard. Each character narrows down which system has the fault. This table shows what each part of the code tells you.

CharacterMeaningWhat It Tells You
PPowertrainThe fault is in the engine or transmission systems.
0Generic (SAE) codeThe definition is the same on every OBD-II vehicle.
5Vehicle speed, idle control and auxiliary inputsThe fault involves vehicle speed, idle control or inputs such as oil pressure, A/C, power steering, system voltage and cruise control.
74Specific faultCruise Control System – Vehicle Speed Too High

What the P0574 Code Means

The SAE J2012 standard defines the P0574 code as Cruise Control System – Vehicle Speed Too High. On most vehicles, the powertrain control module (PCM) runs the cruise control. It reads the cruise switches on the steering wheel or stalk, the brake switch and vehicle speed, then holds speed by moving the electronic throttle. Older vehicles use a cable and a separate servo.

Many vehicles send all the cruise buttons to the PCM on one or two wires through a resistor ladder. Each button gives a different voltage, so the PCM can tell which one is pressed. On steering wheel switches, the signal passes through the clockspring, a coiled ribbon cable behind the steering wheel.

Every PCM has a maximum speed for cruise control, set by the maker. If vehicle speed goes above it while cruise is active, the PCM cancels cruise and may set this code. A faulty vehicle speed signal can make the PCM think the vehicle is going faster than it is.

Symptoms of the Cruise Speed Limit Code

Most cruise faults only affect the cruise control. Common signs of a P0574 code include:

  • Cruise control canceling at high speed
  • Cruise control not working
  • Check engine light on some vehicles
  • Speedometer reading higher than real speed

If the code set after a long downhill or fast highway drive, it may simply have recorded what happened. If it sets at normal speeds, suspect the speed signal.

Common Causes of the P0574 Code

These are the usual causes:

  1. Driving faster than the cruise limit. Often on a long downhill grade.
  2. Faulty vehicle speed signal. A spike makes the speed look too high.
  3. Wrong tire size programmed. Smaller tires can make the speed read high.
  4. Wheel speed sensor problem. On vehicles that use ABS sensors for speed.
  5. PCM software issue. Some makers have released updates.

Tools You Will Need

You can do most of this testing at home with basic tools:

  • OBD-II scan tool that shows cruise switch status
  • Digital multimeter
  • Wiring diagram for your vehicle
  • Trim tools for removing steering wheel covers
  • Contact cleaner

How to Track Down the P0574 Code

Watch the switch status in live data while you press each button. It is the quickest way to see what the PCM sees.

Look at the Freeze Frame

Check the freeze frame data for vehicle speed when the code set. If it shows a high but real speed, such as on a downhill, the code may not point to a fault.

Compare the Speed Signal

Drive at a steady speed and compare scan tool vehicle speed with a GPS app. A big difference, or sudden spikes, points to a speed sensor or tire size problem.

Check the Speed Sensors

Check the vehicle speed sensor or the ABS wheel speed sensors, depending on which your vehicle uses. Look for related codes such as P0500 or ABS codes.

Inspect the sensor wiring for damage and check the connectors for corrosion.

Check for Software Updates

Ask a dealer whether a PCM update exists for your vehicle. Some cruise and speed signal problems have been fixed with new software.

How to Fix the P0574 Code

Match the repair to what your tests found. Then clear the code and drive under the same conditions that set it.

  • Clear the code if it was set by a real high speed.
  • Repair the speed sensor or its wiring.
  • Program the correct tire size.
  • Update the PCM software if one is available.

If the code returns at normal speeds, focus on the speed signal. A signal that spikes for a moment can cancel cruise and set this code even though you were never speeding.

Common Mistakes to Avoid

These mistakes waste money or leave the real fault in place:

  • Replacing parts for a code set by real high speed
  • Ignoring a mismatched tire size
  • Overlooking ABS wheel speed sensor faults

Repair Cost Breakdown

The cost to fix a P0574 code depends on the cause. This table shows typical ranges for parts and labor.

RepairDIY CostTypical Shop Cost
Connector cleaning$5 to $10$50 to $100
Cruise control switch$30 to $150$100 to $300
Clockspring$40 to $200$200 to $500
Brake light switch$10 to $50$75 to $200
Wiring repair$10 to $30$100 to $300

Often this code needs no parts at all. When it points to a speed sensor, the sensor is usually cheap.

Can You Drive with a P0574 Code?

Usually, yes. Cruise control may not work, but the engine, brakes and steering work as normal.

If the code involves the brake switch, check that your brake lights work. Drivers behind you need them, and some vehicles will not shift out of park or will limit power with a faulty brake switch.

Related Codes

These codes often show up with this one or point to the same system:

CodeMeaning
P0565Cruise Control On Signal Malfunction
P0566Cruise Control Off Signal Malfunction
P0567Cruise Control Resume Signal Malfunction
P0568Cruise Control Set Signal Malfunction
P0571Cruise Control/Brake Switch A Circuit Malfunction
P0575Cruise Control Input Circuit

Handling the Cruise Speed Limit Code

A P0574 code means the PCM saw vehicle speed above the cruise limit. Real high speeds, faulty speed signals and wrong tire sizes cause most cases.

  • Check the freeze frame speed.
  • Compare scan tool speed with GPS.
  • Check the speed sensors and wiring.
  • Ask about software updates.

Frequently Asked Questions

What Is the Top Speed for Cruise Control?

It varies by maker and model. Many vehicles allow cruise up to around 85 to 100 mph, but some are lower or higher. If you set cruise and coast downhill past the limit, the PCM cancels it.

Can a Bad Clockspring Cause Cruise Control Codes?

Yes. The clockspring carries the steering wheel switch signals. When it wears out, the cruise buttons can stop working, often along with the horn, the airbag light or other steering wheel buttons. Replacing it needs care, since the airbag must be removed safely.

Why Does My Cruise Control Turn Off by Itself?

The PCM cancels cruise when it sees the brake switch change, a switch signal it does not trust or a vehicle speed problem. A misadjusted brake switch or worn steering wheel switch often causes it.

Is It Safe to Remove the Airbag Myself?

Only if you follow the service manual exactly. Disconnect the battery and wait the specified time, usually several minutes, before unplugging the airbag. Store it face up away from heat. If you are not comfortable doing this, have a shop do it.

Will the Cruise Control Code Affect Engine Performance?

Usually not. Most cruise switch codes only disable the cruise control. Brake switch codes are the exception, since the brake switch can also affect shifting and throttle control on some vehicles.

Can I Replace a Cruise Switch Myself?

Often, yes. Stalk switches usually come off with a few screws after removing the column covers. Steering wheel switches usually need the airbag removed first, so follow the service manual closely. Buy a switch that matches your vehicle’s part number, since resistor values differ between models.

Does Adaptive Cruise Use the Same Switches?

Usually, yes. Adaptive cruise uses the same or similar steering wheel buttons, plus a radar or camera that measures the distance to the car ahead. Switch codes like these can disable both normal and adaptive cruise. Radar or camera faults set different codes, often in another module.

Why Did the Code Appear After Cleaning the Interior?

Spray cleaners and water can get into steering wheel switches and their connectors. The liquid changes the resistance or shorts the contacts, so the PCM sees a wrong or stuck button. Let the switch dry fully, and spray cleaner onto a cloth instead of onto the switch next time.